16
accessories. Service questions can also be an-
swered by calling the factory at 888-714-5294 or
by contacting your local dealer.
To perform any
service to your grill, you must make sure that
the grill is not plugged into an outlet.
Replacing the Digital Control Board.
To perform any service to your grill, you must
make sure that the grill is not plugged into an
outlet.
With an hex key tool, remove the two screws on
the face of the side shelf that attach the control
box to the side shelf. Carefully pull the control
box away from behind the side shelf. With a 5/16
wrench or driver bit, remover the 2 screws on the
bottom of the control box to disassemble the box.
With a hey key tool and 3/8 wrench remove the
screws and nuts that attach the control board to
the control box. Carefully remove the 7 spade
connectors taking note of where each one goes.
Carefully connect the spade connectors to the
new control board. Black wire connects to HOT.
White wire connects to COM. Yellow wire con-
nects to AUG. Blue wire connects to FAN. Red
wire connects to IGN. Brown wires connect to
PROBE 1. Reassemble and reinstall the control
box.
Replace the Digital Control Board Fuse.
To perform any service to your grill, you must
make sure that the grill is not plugged into an
outlet.
To protect the digital control from power surges,
the board is equipped with a 5 amp 250 volt
fuse. To replace the fuse, remove the two screws
underneath the side shelf on the bottom of the
control box. Slide the control box away from the
side shelf exposing the circuit board underneath
the side shelf. Carefully remove the blown fuse
and replace with a new fuse. Reinstall the control
box.
Remove/Replace the Auger and Auger
Motor.
To perform any service to your grill, you must
make sure that the grill is not plugged into an
outlet.
To remove the entire auger assembly, open the
side access panel on the left side of the hopper.
Disconnect the plug labeled “AUG”. Remove the
two screws above and below the auger motor.
The motor with the auger attached will now slide
straight out of the access panel. To remove the
auger motor from the auger assembly, remove
the nut and bolt from the auger sleeve. Reinstall
and reconnect the auger assembly and the auger
connection wire making sure they are clear of the
fan blades.
Remove/Replace the Combustion Fan.
To perform any service to your grill, you must
make sure that the grill is not plugged into an
outlet.
Open the side access panel on the left side of
the hopper. Disconnect the plug labeled “FAN”.
From below the grill, unbolt the fan cage to ex-
pose the combustion fan. Remove the 4 screws
that fasten the fan to the air box. Reinstall the
fan and reconnect the fan wire making sure that
all wires are clear of the fan blades.
Remove/Replace the Ignitor.
To perform any service to your grill, you must
make sure that the grill is not plugged into an
outlet.
Open the side access panel on the left side of
the hopper. Disconnect the plug labeled “IGN”
Remove the 2 screws that fasten the burn pot to
the air box inside the grill. Remove the burn pot
and loosen the ignitor set screw with a hex key
tool. Remove the ignitor from the burn pot and
gently pull the wires through the air box and out
the top of the grill. Thread the new ignitor wires
through the back of the air box and out the small
access hole. Insert the new ignitor into the burn
pot leaving it 1/8” from the end or the ignitor tube.
You will need to align the ignitor bushing with the
set collar before tightening. Tighten the set screw
securing the ignitor in place. Re-install the burn
pot. From the side access panel, connect the new
ignitor to the plug labeled IGN making sure that
all wires are clear of the fan blades.
Remove/Replace the RTD (Temperature
Sensor)
To perform any service to your grill, you must
make sure that the grill is not plugged into an
outlet.
Open the side access panel on the left side of
the hopper. Find and disconnect the plug labeled