SA101NX3-E - 3 / 8 - 07-01-25
O
PERATION OF THE
D
ISPLAY
Values or parameters are selected, as you would read a book. The further down listed groups are arranged as
'pages'. You can scroll forwards and backwards through these groups by pressing the [
→
] and [
←
]
keys. The
entries of each group can be read from top to bottom like lines of a text. Select a line by pressing the keys [
↓
]
(down) and [
↑
] (up). The selection starts again with the other end of the 'page', when the top or bottom of the
'page' is reached.
Hold down the LED T
EST
button and press [
←
] to select directly the A
CTUAL
V
ALUES
group, hold down
LED T
EST
and press [
→
] to display the group C
URRENT
A
LARMS
.
To modify a parameter, first enter the relevant I
DENT
-N
UMBER
. However, parameters of group 0, -
GENERAL
P
ARAMETERS
-, can be modified without entering this number. Parameters are modified as follows:
1. Select the required parameter group with the [
←
] and [
→
] buttons. One or two parameters are displayed.
2. Press O
FF
and LED T
EST
(function: P
ARA ON
or P
ARA OFF
) together. This opens parameterisation mode
as can be seen by the specific cursor [
█
]. The selection of the group cannot be changed now.
3. Select the required parameter line (if two are displayed) with the [
↓
] and [
↑
] buttons.
4. Press O
FF
and A
LARM OFF
(E
NTER
function) together to select the parameter line. The shape of the cursor
confirms the selection, as it underscores (e.g.
1
9
6
) now the part of the parameter that is to be modified.
The chosen parameter cannot be deselected now.
5. Select the figure or letter of the parameter that you want to modify with the [
←
] and [
→
] cursor keys.
Numerical parameters can be increased or decreased by increments of 1 with the [
↑
] and [
↓
] buttons.
Press the same buttons to negate parameters that are displayed with a letter (+/- signs, alarm coding etc.).
6. Press O
FF
and A
LARM OFF
together to store the displayed parameter. Press O
FF
and LED T
EST
instead of
O
FF
and A
LARM OFF
to abort parameterisation.
Display contrast setting
Hold down LED T
EST
and press key [
↑
] to increase the display contrast (makes the display darker) or LED
T
EST
and key [
↓
] to lower it (makes the display lighter).
PIN Number, Ident-Number
To modify a parameter, you first have to enter the relevant I
DENT
-N
UMBER
. This number is compared with
the PIN
NUMBER
, and if they are identically, the user is authorised to parameterise the device. The user can
chose any PIN N
UMBER
between 00000 and 50000. The PIN N
UMBER
and I
DENT
-N
UMBER
are factory set to
00000.
A special I
DENT
-N
UMBER
can be obtained on enquiry from the factory if you forget your PIN N
UMBER
, so
that a new PIN N
UMBER
can be entered. Modify the PIN N
UMBER
as follows:
−
Enter the currently valid I
DENT
-N
UMBER
. The pin number is now also shown.
−
Enter a new PIN N
UMBER
.
−
The I
DENT
-
NUMBER
previously entered is now no longer valid.
The I
DENT
-
NUMBER
is deleted 15 minutes after the last input, if the user has not previously set it to an
invalid value.
The automatic deletion of the I
DENT
-N
UMBER
is however not carried out while 00000 is set as the PIN.
Changes without further notice reserved.
