KUHN Merge Maxx 900 Operator'S Manual Download Page 71

Page: 71 / 114

Instructions for work

Merger

Merge Maxx 900

Windrow delivery two thirds to the left and one

third to the right

- Press simultaneously the selection keys for

approximately 1 second.

- The indicator lights flash for the whole period during

which the conveyor belt direction of rotation is inverted
and then they stay on.

- On headlands, press key activating the inversion of

the conveyor direction of rotation.

- The indicator lights flash for the whole period during

which the conveyor belt direction of rotation is inverted
and then they stay on.

The time delay during which the conveyor belt
direction of rotation is inverted can be adjusted
(See section "Adjustment of the time delay when
inverting the conveyor belt direction of rotation").

Summary of Contents for Merge Maxx 900



















































































































Search results

Summary of Contents for Merge Maxx 900

Reviews:

Related manuals for Merge Maxx 900

Brands by name

Popular brands

KUHN Merge Maxx 900, Operator'S Manual

Search results

Summary of Contents for Merge Maxx 900

Reviews:

Related manuals for Merge Maxx 900

Brands by name

Popular brands