KUHN GF10802T Operator'S Manual Download Page 40 | Manualshive

Page: 40 / 72

background image

Gyrotedder

38

GF10802T

Instructions for transport

2. Conformity with the road regulations

- Check that reflectors are clean.

Before driving the machine on public roads,
ensure that the machine complies with
current highway code regulations.

Never tow the machine at a speed exceeding
40 km/h (25 mph).

Instructions specific to France:

Never tow the machine at a speed exceeding
25 km/h (15,5 mph).

Check that transport locks (1) are fully
engaged.

Regularly check the tyre pressure.

Make sure the release cord cannot be
operated inadvertently.

«
...
38
39
40
41
42
...
»

Summary of Contents for GF10802T









































































Reviews:

No comments

Related manuals for GF10802T

Brand: Sagola Pages: 8

Brand: Panasonic Pages: 180

Brand: Backyard Discovery Pages: 79

Brand: Badger Meter Pages: 16

Brand: Cadman Pages: 84

GPSMAP 188 Sounder

Brand: Garmin Pages: 134

Brand: Yamaha Pages: 4

Brand: Wacker Neuson Pages: 120

Brand: YOKOGAWA Pages: 75

Brand: A.J.Antunes Pages: 24

Brand: B&G Pages: 2

Brand: popular Pages: 27

SpinVessel 650ml

Brand: V&P Scientific Pages: 9

LED Studio 3300D

Brand: PR Lighting Pages: 16

Brand: Old Town Canoe Co. Pages: 1

WEIDER SHAPE GLIDER WECR43062

Brand: ICON Health & Fitness Pages: 6

Brand: Duracell Pages: 2

Brand: XPOtool Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands