KUHN GF10802T Operator'S Manual Download Page 59 | Manualshive

Page: 59 / 72

background image

Maintenance and storage

Gyrotedder

GF10802T

57

Replacing a tine

Before leaving the tractor or before
adjusting, maintaining or repairing the
machine, disengage the PTO drive, turn off
the engine, remove ignition key and wait until
all moving parts have come to a complete
stop and apply park brake.

2 types of tines are fitted on the machine:

- Tines (1) for rotors rotating clockwise

(a).

- Tines (2) for rotors rotating

counterclockwise (b).

Check that the tines are fitted properly with
regards to the rotor direction of rotation.

«
...
57
58
59
60
61
...
»

Summary of Contents for GF10802T









































































Reviews:

No comments

Related manuals for GF10802T

Brand: ZOLL Pages: 344

Brand: ABB Pages: 9

Brand: Tanco Pages: 72

Brand: HABYS Pages: 16

Brand: Acterna Pages: 72

Brand: Unex Pages: 5

DVCPRO P2 Series

Brand: Panasonic Pages: 32

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: Eastern Jungle Gym Pages: 17

Brand: Vahle Pages: 96

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Brand: Task Force Tips Pages: 20

Brand: Mackie Pages: 18

Brand: Mackie Pages: 2

Brand: Mackie Pages: 8

Brand: Mackie Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands