Kubota LA1154 Assembly Instructions Manual Download Page 50 | Manualshive

Page: 50 / 63

background image

ASSEMBLY INSTRUCTIONS

48

5. Pass the control lever wire harness and the ON/OFF

switch wire harness, as shown in the figure. Fix these
harnesses and the lever cable with the cord band.

A

Tilt the control lever toward the front left of the tractor,
as shown in the figure, to make sure the control lever
wire harness becomes too tight.

6. Cover the control lever cable and the wire harnesses

with the sleeve (original). Using the cord band, secure
these parts back into position.

7. Using the cord band, fix the control lever wire harness

and the control lever cable, located below the step, as
shown in the figure.

8. Attach the relay to the wire hanress, and connect the

wire harness to the tractor and solenoid valve harness.

A

Connect the wire harness couplers of the 3rd function
control lever to their respective same-color couplers.

(1) Control lever harness
(2) ON/OFF switch harness
(3) Lever cable
(4) 2-cord bands

(A) 110 to 130 mm
(4.3 to 5.1 in.)
(B) 110 to 150 mm
(4.3 to 5.9 in.)

(1) Control lever haraness

(A) Toward the tractor front
(B) Toward the tractor left side

(1) Lever harness
(2) Lever cable
(3) Clamp (cord band)

(A) To control lever

(A) To 3rd function control lever
(B) To ON/OFF switch
(C) To tractor harness
(D) To solenoid valve harness-1
(E) To solenoid valve harness-2
(F) To relay
(G) To relay

«
...
48
49
50
51
52
...
»

Summary of Contents for LA1154
































































Reviews:

No comments

Related manuals for LA1154

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: FENDT Pages: 31

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

APT-9411 Series

Brand: TAKAYA Pages: 77

Brand: Tadano Pages: 402

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

Brand: Tar River Pages: 26

Brand: ZOLL Pages: 38

Brand: ZOLL Pages: 36

Nature2 Fusion soft

Brand: Zodiac Pool Systems Pages: 52

Brand: Oliver Pages: 38

Brand: G21 Pages: 7

Brand: RainPoint Pages: 40

Brand: FARM-MAXX Pages: 35

LUXOMAT net PBM-KNX-DX-4W

Brand: B.E.G. Pages: 16

Brand: Woods Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands