manualshive.com logo in svg

Kubota BX2350D, Operator'S Manual

Share
Download
Kubota BX2350D Operator'S Manual Download Page 67

47

CAB OPERATION

ENGLISH

B

Operation

C

Temperature adjustment 

If warmer temperature is required, put the dial at the
position (A). If you want to lower the temperature, turn the
dial from the position (A) to the position (B). 

CAB ACCESSORY

B

Sun Visor

To improve comfort and security when the sun reduces
front windscreen visibility, put the sun visor at lowered
position as shown in the figure.
When it is not necessary, put the sun visor at the original
position as shown in the figure.

BEACON (if equipped)

B

Beacon Light Switch

To light the beacon, press switch where the yellow label is
applied.
To stop the turning light (beacon), press the upper part of
the switch.

B

Beacon Position

In order to see beacon in all directions by the other road
users, put the beacon at the top position as shown in the
figure.
In order not to damage the turning light, when the height
is limited (under a building for example) or when there are
some obstacles (branches for example), move beacon to
the bottom position as shown in the figure.

(1) Dial

(A) "RAISE TEMPERATURE" 
(B) "LOWER TEMPERATURE"

(1) Sun visor

(A) Lowered position
(B) Original position

(1) Beacon light switch

(A) "TURN ON"
(B) "TURN OFF"

(1) Beacon

(A) Top position
(B) Bottom position
(C) CAB
(M) "MOVE"

Summary of Contents for BX2350D







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands