manualshive.com logo in svg

Kubota BX2350D, Operator'S Manual

Share
Download
Kubota BX2350D Operator'S Manual Download Page 101

81

APPENDICES

ENGLISH

PTO Clutch Lever.............................................28
PTO Drive Shaft ...............................................29
PTO Select Lever .............................................27
PTO Shaft Cover and Shaft Cap ......................28
Radiator Hose (Water pipes)............................72
Radiator Hoses and Clamps ............................66
Range Gear Shift Lever (Hi-Lo)........................19
Rear Ballast......................................................42
Rear Wheels.....................................................40
Rear Window....................................................44
Rear Work Light ...............................................48
Refueling ..........................................................54
Remote Control Valve Coupler Connecting and

Disconnecting ...............................................33

Remote Control Valve Lever ............................33
Safety Devices .................................................58
Seat Belt...........................................................15
Seat Belt and ROPS.........................................57
Speed Control Pedal ........................................20
Speed Set Device.............................................21
Stationary PTO.................................................28
Stopping ...........................................................21
Sun Visor..........................................................47
Toe-in ...............................................................67
Top Link............................................................31
Tractor Lights ...................................................17
Trailer Electrical Outlet .....................................26
Trailer Load Capacity .......................................79
Transmission Fluid ...........................................68
Transmission Fluid Level..................................55
Transmission Oil Filter......................................66
Transmission Strainer ......................................69
Transport the Tractor Safely.............................26
Turn Signal Light Switch...................................16
Using the Wipers in Cold Season.....................45
Valve Lock........................................................36
Walk Around Inspection ...................................54
Warm-up and Transmission Oil in the Low

Temperature Range .....................................13

Washer Fluid Tank ...........................................45
Wheel Bolt Torque............................................59
Work Light Switch.............................................48

Summary of Contents for BX2350D







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands