Kubota BX2350D Operator'S Manual Download Page 6

Page: 6 / 102

CONTENTS

ENGLISH

PARKING ............................................................................................................... 24

Parking............................................................................................................................ 24

ACCESSORY......................................................................................................... 24

12V Electric Outlet .......................................................................................................... 24

OPERATING TECHNIQUES ................................................................................. 25

PTO ........................................................................................................................... 27

PTO OPERATION.................................................................................................. 27

THREE-POINT HITCH & DRAWBAR........................................................................ 30

3 -POINT HITCH .................................................................................................... 31

DRAWBAR............................................................................................................. 31

HYDRAULIC UNIT..................................................................................................... 32

3-POINT HITCH CONTROL SYSTEM................................................................... 32

Hydraulic Control ............................................................................................................ 32
3-point Hitch Lowering Speed......................................................................................... 32

REMOTE HYDRAULIC CONTROL SYSTEM........................................................ 33

Remote Control Valve Coupler Connecting and Disconnecting ..................................... 33
Remote Control Valve Lever........................................................................................... 33

AUXILIARY HYDRAULICS .................................................................................... 34

Hydraulic Outlet .............................................................................................................. 34

MOWER LIFT LINKAGE SYSTEM ........................................................................ 34

Cutting Height Control Dial ............................................................................................. 34
Hydraulic Control Unit Use Reference Chart .................................................................. 35

AUXILIARY HYDRAULIC CONTROL VALVE (IF EQUIPPED) ............................. 36

Valve Lock ...................................................................................................................... 36
Auxiliary Hydraulic Ports................................................................................................. 36
Control Lever and Hydraulic Hose Connections............................................................. 37
Controlling Loader (Only if equipped with loader)........................................................... 38

TIRES, WHEELS AND BALLAST.............................................................................. 39

TIRES..................................................................................................................... 39

Summary of Contents for BX2350D







































































































Search results

Summary of Contents for BX2350D

Reviews:

Brands by name

Popular brands

Kubota BX2350D, Operator'S Manual

Search results

Summary of Contents for BX2350D

Reviews:

Brands by name

Popular brands