background image

3

WORK

13

M01123-10

(All SX models)

Turn filler cap

counterclockwise and lift it off.

B02073-10

(All XC models)

Press release button

, turn the filler cap counterclockwise, and lift it off.

3.12

Closing the filler cap

M01123-11

(All SX models)

Mount filler cap

and turn it clockwise until the fuel tank is tightly closed.

Info

Run the fuel tank breather hose

without kinks.

B02073-11

(All XC models)

Mount filler cap

and turn it clockwise until the release button engages.

Info

Run the fuel tank breather hose

without kinks.

3.13

Refueling

Danger

Fire hazard

Fuel is highly flammable.

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with
the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with
soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that is contaminated with fuel.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

Do not allow fuel to get into the ground water, the ground, or the sewage system.

Summary of Contents for 125 SX 2016























Reviews: