manualshive.com logo in svg

KSB UPAchrom CC, Installation & Operating Manual

Share
Download
KSB UPAchrom CC Installation & Operating Manual Download Page 21

5 Installation at Site

21 of 44

UPAchrom

V

W

U

Risol

(MΩ)

M 3~

V1

W1

U1

Risol

(MΩ)

M 3~

V2

W2

U2

V1-1 W1-1

U1-1

Risol

(MΩ)

M 3~

V1-2 W1-2

U1-2

1 cable

2 cables (for both star and
delta operation)

2 cables (parallel)

5.2 Installing the pump set in a vertical position

 DANGER

Using damaged cables in a well

Electric shock!

▷

Do not kink cables (observe the minimum bending radius

6)

 of the cable) or drag

the cables over sharp edges.

▷

Use cable ties or other suitable fasteners to fasten the power cables as well as
any measuring and control cables to the riser or piping 

every three meters

.

▷

Do not use any tools, equipment or accessories with sharp edges (e.g. sharp-
edged pipe sockets) during installation.

 WARNING

Persons could fall into unsecured wells/reservoirs/tanks

Risk of personal injury!

▷

During installation work, take suitable precautions to protect anyone from
falling into an open well/reservoir/tank.

▷

Suitably fence off the work area.

CAUTION

Risk of the pump set falling into the well/reservoir/tank

Damage to the pump set!

▷

Secure the pump set during the entire installation procedure.

▷

Dimension any securing devices (supporting clamps, supports, etc.) so that they
can carry all weights during the installation.

6)

See cable manufacturer's documentation or DIN VDE 0298-3.

Summary of Contents for UPAchrom CC













































Reviews:

No comments

Brands by name

Popular brands

Load more brands