Krone OPTISOUND 3030 C Handbook Download Page 7

Page: 7 / 52

3 Product description

OPTISOUND 3030 C • Foundation Fieldbus

51118-EN-210701

3 Product description

3.1 Configuration

The scope of delivery encompasses:

•

OPTISOUND 3030 C ultrasonic sensor

•

Optionally mounting strap or compression flange

•

Documentation

– This operating instructions manual

–

Ex-specific afety instructions (with Ex versions)

– Operating instructions "

Display and adjustment module

(optional)

–

If necessary, further certificates

Information:

Optional instrument features are also described in this operating

instructions manual. The respective scope of delivery results from the

order specification.

The OPTISOUND 3030 C consists of the components:

•

Process fitting with transducer

•

Housing with electronics

•

Housing lid with integrated display and adjustment module

(optional)

The components are available in different versions.

Fig. 1: OPTISOUND 3030 C, plastic housing
1 Housing lid with integrated display and adjustment module (optional)

2 Housing with electronics

3 Process fitting with transducer

The type label contains the most important data for identification and

use of the instrument:

•

Instrument type

•

Article and serial number device

•

Article numbers, documentation

Scope of delivery

Constituent parts

Type label

Summary of Contents for OPTISOUND 3030 C





















































Search results

Summary of Contents for OPTISOUND 3030 C

Reviews:

Related manuals for OPTISOUND 3030 C

Brands by name

Popular brands

Krone OPTISOUND 3030 C, Handbook

Search results

Summary of Contents for OPTISOUND 3030 C

Reviews:

Related manuals for OPTISOUND 3030 C

Brands by name

Popular brands