manualshive.com logo in svg

Krone AM 203 CV, Operating Instructions Manual

Share
Download
Krone AM 203 CV Operating Instructions Manual Download Page 36

34

7. Winter storage

•

Store the machine in a dry place that is not near
artificial fertilizers.

•

Clean the machine thoroughly from the inside and the
outside. Dirt attracts moisture and causes corrosion.
When cleaning the machine with high pressure water
jet cleaners, do not aim the water jet at the bearings.

•

Check moving parts (joints etc.) for freedom of
movement, and if necessary remove them, clean
them and check for wear. If necessary, replace them
with new parts.

•

Lubricate all moving parts.

•

Thoroughly grease the machine.

•

Grease the protective tubes of the PTO shaft to
prevent it from freezing.

•

Touch up the paint work. Thoroughly treat any bare
metal with rust protection.

•

Make a list of all replacement parts required, and
order them in good time. It is easier for your KRONE
dealer to obtain and fit the required parts out of the
main season. This ensures that your machine is fully
operational for the coming season.

8. Start-up after winter storage

•

Wipe off the grease and oil used for machine
conservation.

•

Carry out in full the steps described in the chapter on
maintenance.

•

Spin the friction clutch to release sticking friction
surfaces.

•

Once bled the overload clutch has to be released by
switching on the pto with the mower attached to the
tractor: the universal drive shaft must rotate freely up
to the clutch hub, whilst the mowing discs must not
rotate (also see section 4.8)

•

Carefully read through the operating instructions
again.

Summary of Contents for AM 203 CV

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands