background image

 SAFETY INSTRUCTIONS 

1

3

OPTIFLEX 1100 C

www.krohne.com

01/2012 - 4001226201 - QS OPTIFLEX 1100 R01 en

Warnings and symbols used

HANDLING

•  

This symbol designates all instructions for actions to be carried out by the operator in the 

specified sequence.

i

RESULT

RESULT

RESULT

RESULT
This symbol refers to all important consequences of the previous actions.

Safety instructions for the operator

DANGER!

This information refers to the immediate danger when working with electricity.

DANGER!

These warnings must be observed without fail. Even partial disregard of this warning can lead to 
serious health problems and even death. There is also the risk of seriously damaging the device 
or parts of the operator's plant.

WARNING!

Disregarding this safety warning, even if only in part, poses the risk of serious health problems. 
There is also the risk of damaging the device or parts of the operator's plant.

CAUTION!

Disregarding these instructions can result in damage to the device or to parts of the operator's 
plant.

INFORMATION!

These instructions contain important information for the handling of the device.

CAUTION!

Installation, assembly, start-up and maintenance may only be performed by appropriately 
trained personnel. The regional occupational health and safety directives must always be 
observed.

LEGAL NOTICE!

The responsibility as to the suitability and intended use of this device rests solely with the user. 
The supplier assumes no responsibility in the event of improper use by the customer. Improper 
installation and operation may lead to loss of warranty. In addition, the "Terms and Conditions of 
Sale" apply which form the basis of the purchase contract.

INFORMATION!

Further information can be found in the handbook and on the data sheet. These documents 
can be downloaded from the website (Download Center).

If you need to return the device to the manufacturer or supplier, please fill out the device 
return form and send it with the device. Unfortunately, the manufacturer cannot repair or 
inspect the device without the completed form. The form can be found in the handbook or 
downloaded from the website. Click on the "Service" tab on one of the web pages and read 
the instructions.

Summary of Contents for OPTIFLEX 1100 C





















Reviews: