background image

1

 SAFETY INSTRUCTIONS 

OPTIBRIDGE

www.krohne.com

07/2016 - 4004307801 - MA OPTIBRIDGE R01 en

1.3.1  ATEX conformity

The manufacturer declares with the EU declaration of conformity on his own responsibility 
conformity with the protection goals of directive 2014/34/EU. Conformity with harmonised 
standards was checked in accordance with EN 60079-0:2012 and EN 60079-11:2012. The EU 
declaration of conformity is based on the EC type examination certificate: ZELM 16 ATEX 0557. 
You can download the EC Type-Examination-Certificate from the manufacturer's website.

The Ex marking reads as follows: II (1) G [Ex ia] IIC

1.3.2  Approval according to the IECEx scheme

Conformity with IECEx standards was tested in accordance with the IECEx Certification Scheme 
for Explosive Atmospheres acc. to IEC 60079-0:2011, IEC 60079-11:2012. The number of the 
IECEx certificate is:

You can download the IECEx certificate from the official IECEx website www.iecex.com or from 
the manufacturer's website. 

1.4  Safety instructions from the manufacturer

1.4.1  Copyright and data protection

The contents of this document have been created with great care. Nevertheless, we provide no 
guarantee that the contents are correct, complete or up-to-date.

The contents and works in this document are subject to copyright. Contributions from third 
parties are identified as such. Reproduction, processing, dissemination and any type of use 
beyond what is permitted under copyright requires written authorisation from the respective 
author and/or the manufacturer.

The manufacturer tries always to observe the copyrights of others, and to draw on works created 
in-house or works in the public domain.

The collection of personal data (such as names, street addresses or e-mail addresses) in the 
manufacturer's documents is always on a voluntary basis whenever possible. Whenever 
feasible, it is always possible to make use of the offerings and services without providing any 
personal data.

We draw your attention to the fact that data transmission over the Internet (e.g. when 
communicating by e-mail) may involve gaps in security. It is not possible to protect such data 
completely against access by third parties. 

We hereby expressly prohibit the use of the contact data published as part of our duty to publish 
an imprint for the purpose of sending us any advertising or informational materials that we have 
not expressly requested. 

IECEx ZLM 16.0005

IECEx ZLM 16.0005

IECEx ZLM 16.0005

IECEx ZLM 16.0005

Summary of Contents for OPTIBRIDGE

































Reviews: