background image

4

 ELECTRICAL CONNECTIONS 

10 

ESK4... ...

www.krohne.com

10/2017 - 4001078703 - AD ESK4 Ex II2G R03 en

4.1  General notes

The electrical connection of the intrinsically safe signal circuit with protection level "ia" to the 
modules ESK4... , ESK4-FF and ESK4-PA is independent of polarity.
The connection of the ESK4-I/O module is polarity sensitive.
The connection to all modules is made by colour-coded pluggable connection terminals. The 
colour coding of the terminals must be observed. The permissible maximum values of the 
separate circuits (electrical data) must be observed.

The connecting cables must be selected according to prevailing installation standards 
(e.g. EN 60079-14). The connecting cables must be fixed and laid so they are sufficiently 
protected against damage.

All cores that are not used must be securely connected to the ground potential of the hazardous 
area or carefully insulated against each other and against ground (test voltage 

500 V

eff

).

4.2  Power supply

Electronic signal outputs do not require a separate power supply. The required supply is 
provided via the 4...20 mA current output or bus-connection.

4.3  Internal connections

All modules should be connected internally using the ribbon cables provided. These are non-
interchangeable and protected against reverse polarity.

Summary of Contents for ESK4 Series

















Reviews: