manualshive.com logo in svg

Krix Tektonix, Owner'S Manual, Page: 11 / 12

Share
Download
Krix Tektonix Owner'S Manual Download Page 11

Due to continued development specifications may change without notice.

Volcanix: specifications

Drivers

Bass Driver

Electronics

Amplifier Power
Amplifier S/N
Distortion

 

-

 

Input to Speaker

Line Level Inputs

General

Frequency Range
Output
Auto Power On / Off
Phase Select
Filters 

Cabinet

Enclosure Type
Dimensions
Material
Finish
Weight

Nominal 305mm (12”) diameter paper cone driver, 50mm long throw 
voice coil, developed for high level, low frequency reinforcement

450 watts RMS into the nominal 4 ohm driver
>90dB
<0.1% - @ 400 watts RMS
Left Input (mono)   

300mV RMS for maximum output

Left + Right Input (stereo) 

150mV RMS for maximum output

16Hz - 200Hz (-6dB) in room response
125dB maximum SPL in room response
15 minute delay before switching to standby after no input signal
0° or 180° (relative to input signal)
Low pass filter 50-195Hz, Bypass
High pass filter to limit driver excursion below 22Hz

Bass reflex, front vented
506mm high x 400mm wide x 470mm deep (including grille and feet)
18mm MDF
Vinyl or lacquered timber veneer
23kg

specification

warranty

5 year warranty applies to the cabinet and 
speaker.

2 year warranty applies to the amplifier and 
related internal electronics.

(Refer to the details on the warranty card 
supplied)

queries

If you have any queries regarding the Tektonix 
or Volcanix setup procedure or any other Krix 
product, please contact your nearest Krix 
retailer or Krix directly. Contact details are on 
the back cover of this booklet.

Tektonix: specifications

Drivers

Bass Driver

Electronics

Amplifier Power
Amplifier S/N
Distortion

 

-

 

Input to Speaker

Line Level Inputs

General

Frequency Range
Output
Auto Power On / Off
Phase Select
Filters 

Cabinet

Enclosure Type
Dimensions
Material
Finish
Weight

Nominal 275mm (11”) diameter paper cone driver, 50mm long throw 
voice coil, developed for high level, low frequency reinforcement

450 watts RMS into the nominal 4 ohm driver
>90dB
<0.1% - @ 400 watts RMS
Left Input (mono)   

300mV RMS for maximum output

Left + Right Input (stereo) 

150mV RMS for maximum output

22Hz - 200Hz (-6dB) in room response
123dB maximum SPL in room response
15 minute delay before switching to standby after no input signal
0° or 180° (relative to input signal)
Low pass filter 50-195Hz, Bypass
High pass filter to limit driver excursion below 26Hz

Bass reflex, front vented
451mm high x 360mm wide x 415mm deep (including grille and feet)
18mm MDF
Vinyl or lacquered timber veneer
18kg

11

Summary of Contents for Tektonix













Reviews:

No comments