This product is for use on a nominal 120 volt circuit and has a
grounding plug that looks like the plug illustrated below. A
temporary adapter which looks like the adapter illustrated in the
figure below may be used to connect this plug to a 2 pole
receptacle as shown if a properly grounded outlet is not available.
The temporary adapter should be used only until a properly
grounded outlet as shown below can be installed by a qualified
electrician. The green colored rigid ear lug or the grounding
wire extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place
by a metal screw.
SPECIFICATIONS
Weight ..............................25 lbs. (stand model)
31 lbs. (cart model)
Capacity ...........................Up to .25 gallon (1 liter) per minute.
(K2015 and K20155 Series)
Up to .33 gallon (1.25 liters) per
minute. (K3017 Series)
Up to .42 gallon (1.6 liters) per
minute (K4019 Series)
Power source ...................1/2 Hp universal motor (K20155 and
K2015 Series)
5/8 Hp permanent magnet DC motor
(K3017 Series)
3/4 Hp permanent magnet DC motor
(K4019 Series)
Power requirement ...........15 amp minimum circuit on 115
VAC, 60 Hz current.
Generator .........................15 amp A/C.
Spraying pressure ............Up to 2800 psi.
Safety features .................Spray gun trigger lock and pressure
diffuser; built-in tip safety guard;
priming knob for safe pressure
release.
Capability..........................Sprays a variety of paints, oil base
latex, primers, stains, preservatives
and other nonabrasive materials,
including pesticides and liquid
fertilizers.
Unit Tip Size
:
Supplied
Max. Size Supports
K2015, K20155
.013
.015
K3017
.015
.017
K4019
.017
.019
NOTE: This pump is available in two models: a stand
model and a cart model. The stand model is
shown in this manual. All information given for
the stand model applies to the cart model
except where indicated.
Grounded Outlet
Grounding Pin
Tab for
Grounding Screw
Adapter
Metal Screw
Cover for grounded outlet box
4
© 2000 Krebs - All rights reserved.
COMPONENTS
The shipping carton for your painting system contains the
following:
• Suction set and return tube
• Spray gun with filter
• Spray tip assembly
• 25 foot long, 1/4 inch diameter pressure hose (K20155
and K2015)
• 50 foot long, 1/4 inch diameter pressure hose (K3017, K4019)
• Packing lubricant
GENERAL DESCRIPTION
This high performance piston pump is a precision power tool
used for spraying many types of materials. Read and follow
this instruction manual carefully for proper operating
instructions, maintenance and safety information.
Controls and Functions
ON/OFF Switch ................The ON/OFF switch turns the unit on
and off.
Suction Set .......................Fluid is drawn through the suction
set into the pump.
Fluid Section ....................A piston in the fluid section moves
up and down to create the suction
that draws fluid through the suction
set.
Spray Gun ........................The spray gun controls the delivery
of the fluid being pumped.
Spray Hose ......................The spray hose connects the gun to
the pump.
Return Tube......................Fluid is sent back out through the
return tube to the original container.
PRIME/SPRAY Knob........The PRIME/SPRAY knob directs
fluid to the spray hose when set to
SPRAY or the return tube when set
to PRIME. The arrows on the
PRIME/SPRAY knob shows the
rotation directions for PRIME and
SPRAY.
Pressure Control Dial .......The pressure control dial controls
the amount of force the pump uses
to push the fluid.
PRIME/SPRAY
Knob
PRIME/SPRAY
Knob
Fluid Section
Suction Set
Return Tube
ON/OFF Switch
(Rear View)
Spray Hose
Spray Gun
Pressure Control
Dial
English
0512719A.qrk 21/12/00 1:30 PM Page 4
Summary of Contents for K2015
Page 42: ......
