![background image](http://html1.mh-extra.com/html/kramer/vp-23rc/vp-23rc_user-manual_2001229016.webp)
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your Presentation Switcher / Controller
12
Table 3: Rear Panel VP-23RC Presentation Switcher / Controller Features
#
Feature
Function
1
MIC IN
Connector
Connect to the microphone
2
COND. / DYN
Selector Switch
Push in to select a condenser, release to select a
dynamic microphone
3
CV OUT
Terminal Block Connector
Connect to the composite video balanced audio acceptor
4
Y/C OUT
Terminal Block Connector
Connect to the s-Video balanced audio acceptor
5
UXGA
OUT
Terminal Block Connector Connect to the VGA/UXGA balanced audio acceptor
6
MASTER OUT
Terminal Block Connector Connect the master balanced audio channel acceptor
1
7
CV IN
Terminal Block Connectors
Connect to the composite video balanced audio sources
2
8
Y/C IN
Terminal Block Connectors
Connect to the s-Video balanced audio sources
2
9
UXGA IN
Terminal Block
Connectors
Connect to the VGA/UXGA balanced audio sources
2
10
A
U
D
IO
SPKR OUT
Terminal Block Connector Connect to a pair of loudspeakers
11
RELAY
Terminal Block Connector
Connect each relay
2
to a room item. The PINOUT is:
NO: Normally Open; C: Common; NC: Normally
Closed
12
IR
Terminal Block Connectors
Connect to an IR emitter cable (from IR1 to IR 3)
13
ETHERNET
Connector
Connects to the PC through computer networking
3
14
Port
1:Terminal Block
Connector (G, Rx, Tx)
4
15
RS-232
Ports
Port 2: 9-pin D-sub Connector
Connect to the RS-232 port of the A/V equipment or a
PC or other Serial Controller
16
C
O
N
TR
O
LL
E
R
PROGRAM
Dipswitches
DIP1 is for firmware upgrade (see section 10.2); DIP 3
is for factory reset; DIP 2 and DIP 4 are not used (see
section 7.1)
17
CV
IN
BNC Connectors
Connect to the composite video sources
2
18
CV
OUT
BNC Connector
Connect to the composite video acceptor
19
Y/C
IN
4-pin Connectors
Connect to the s-Video sources
2
20
Y/C
OUT
4-pin Connector
Connect to the s-Video acceptor
21
UXGA
IN
15-pin HD Connectors
Connect to the VGA/UXGA video sources
2
22
UXGA
OUT
15-pin HD Connector
Connect to the VGA/UXGA video acceptor
23
V
ID
E
O
UXGA CAT5 OUT
RJ-45 Connector
Connect to a remote computer graphics acceptor via
a receiver (for example, the
TP-120
), see section 3.2
24
RS-232
9-pin D-sub Port
Connect to a PC to control the
VP-23RC
25
FLASH PROG.
Button
Push in to upgrade the Presentation Switcher section to
the latest Kramer firmware (see section 10.1), or
release for Normal (the factory default)
26
RS-485
Terminal Block Port
Pins B (-) and A (+) are for RS-485; Pin G may be
connected to the shield (if required)
27
S
W
IT
C
H
E
R
C
O
N
TR
O
L
Dipswitches
DIPs 1, 2 and 3 are OFF, DIP 4 is ON for RS-485
termination
28 Power Connector with Fuse
AC connector enabling power supply to the unit
1 Both the MASTER OUT and the SPKR OUT terminal block connectors receive the same signal: the MASTER OUT
outputs the signal as it is while the SPKR OUT is amplified
2 From 1 to 4
3 To configure the Media/Room Controller section or control the VP-23RC via the ETHERNET
4 Port 1 can connect to a PC to upgrade the firmware of the Media/Room Controller section