background image

 

TP-46N - Connecting a Component/UXGA/Audio Distribution System 

 

4.1 

Connecting the System in UXGA Mode 

To configure a 

TP-46N

 component/UXGA/audio distribution system in the UXGA 

mode (using up to 300ft (100m) of UTP cabling), as shown in 

Figure 2

, do the 

following: 

1.  On the 

TP-45

 or 

TP-45RC

, connect the following: 

 

An UXGA source (for example, the graphics card on a laptop) to the 

UXGA 15-pin HD (F) connector 

 

An analog audio source to the ANALOG AUDIO 3.5mm mini jack (or a 

digital audio source to the S/PDIF RCA connector), for example, using 

a Kramer C-GMA/GMA cable (VGA 15-pin HD (M) with audio jack to 

VGA 15-pin HD (M) with audio jack) 

Cables are not supplied. The complete list of Kramer cables is on our Web site at 

http://www.kramerelectronics.com.

 

2.  On the 

TP-45

, use the SELECT buttons as follows: 

 

Press the video SELECT button to choose the UXGA input 

 

Press the audio SELECT button to choose S/PDIF 

 

Release the audio SELECT button to choose analog audio

 

 

3.  On the 

TP-45RC

, use the SELECT buttons as follows: 

 

Momentarily press the video SELECT button. The UXGA LED lights 

when the UXGA input is selected 

 

Momentarily press the AUDIO SELECT button to toggle between the 

S/PDIF and analog audio inputs 

The analog audio LED lights when analog audio is selected. 

4.  On the 

TP-46N

, connect the following: 

 

The UXGA OUT 15-pin HD (F) connector to the UXGA acceptor (for 

example, a display) 

 

The ANALOG AUDIO

 

3.5mm mini jack to the analog

 

audio acceptor 

(for example, speakers) 

Alternatively, you can connect a digital audio acceptor to the S/PDIF RCA 
connector, or you can connect both. 

 

Summary of Contents for TP-46N



















Reviews: