background image

 

10 

TP-45EDID - Connecting a Component/XGA – Audio Distribution System 

 

5.1 

Connecting the System in XGA Mode 

To configure a 

TP-45EDID

 and 

TP-46N

 Component/XGA – Audio distribution 

system (using up to 300ft (100m) of UTP cabling) in the XGA mode, as illustrated 

in the example in 

Figure 2

, do the following: 

1.  On the 

TP-45EDID

, connect the following: 

 

An XGA source (for example, the graphics card on a laptop) to the 

XGA 15-pin HD (F) connector 

 

An analog audio source to the ANALOG AUDIO 3.5mm mini jack (or a 

digital audio source to the S/PDIF RCA connector), for example, using 

a Kramer C-GMA/GMA cable (VGA 15-pin HD (M) with audio jack to 

VGA 15-pin HD (M) with audio jack 

2.  On the 

TP-45EDID

, use the SELECT buttons as follows: 

 

Momentarily press the video SELECT button. The UXGA LED lights 

when the UXGA input is selected 

 

Momentarily press the AUDIO SELECT button to toggle between the 

S/PDIF and analog audio inputs 

3.  On the 

TP-46N

, connect the following: 

 

The XGA OUT 15-pin HD (F) connector to the XGA acceptor (for 

example, a display) 

 

The ANALOG AUDIO

 

3.5mm mini jack to the analog

 

audio acceptor 

(for example, powered speakers) 

4.  Connect the LINE OUTPUT RJ-45 connector on the 

TP-45EDID 

to the

 

LINE IN 

RJ-45 connector on the 

TP-46N

, via CAT 5 cabling, see 

Figure 5

5.  Connect the 12V DC power adapter to the power socket and connect the 

adapter to the mains electricity on both the 

TP-45EDID 

and the 

TP-46N

 (not 

shown). 

The signal from the XGA source is transmitted via CAT 5 cable, decoded 

and converted at the XGA OUT 15-pin HD (F) connector to the XGA 

acceptor. 

6.  If required, connect the LINE OUT RJ-45 connector on the 

TP-46N

 to an 

additional 

TP-46N

Summary of Contents for TP-45EDID






















Reviews: