Kramer TP-145 User Manual Download Page 5

Overview 

 

and RS-232 control signals. The 

TP-145

 and 

TP-146

 together form a computer 

graphics/audio/control data line transmitter/receiver system. 

More specifically, the products feature: 

 

Resolution up to WUXGA 1920 x 1200 

 

HDTV compatibility 

 

EDID capture and status indication (

TP-145

 

Simultaneous unbalanced stereo and S/PDIF (24-bit 48kHz) audio outputs 
(

TP-146

 

Level (gain) and EQ (peaking) controls (

TP-146

 

Full duplex RS-232 transmission 

 

Increased level of protection against noise, spikes, and interference in adverse 
environments  

 

System range up to 200m (656ft) 

3.1 

Shielded Twisted Pair/Unshielded Twisted Pair 

We recommend that you use Shielded Twisted Pair (STP) cable. There are 
different categories of STP cable available and we advise you to use the best 
quality STP cable that you can afford. Our non-skew-free cable, Kramer 

BC-STP

 

is intended for digital signals and for analog signals where skewing is not an issue. 
For cases where there is skewing, our Unshielded Twisted Pair (UTP) skew-free 
cable, Kramer 

BC-XTP

, may be used. Bear in mind though, that we advise using 

STP cables where possible, since the compliance to electromagnetic interference 
has been tested using STP cables. 

Although UTP cable might be preferred for long range applications, the UTP cable 
should be installed as far as possible from electric cables, motors, and so on, which 
often create electrical interference.  

However, since the use of UTP cable might cause non-conformity to 
electromagnetic standards, Kramer does not commit to meeting the standard with 
UTP cable. 

3.2 

Defining the EDID 

EDID (Extended Display Identification Data

1

The EDID includes information, such as, the name of the manufacturer, product 
type, timing data supported by the display, display size, luminance data, and (for 
digital displays only) the pixel mapping data. 

) is a data-structure that the display 

provides to describe its capabilities to a graphics card connected to the display’s 
source. The EDID enables the source, such as a PC, to “know” what kind of 
monitor is connected to the output.  

                                                       

 

1 EDID is defined by a standard published by the Video Electronics Standards Association (VESA) 

Summary of Contents for TP-145
















Reviews: