manualshive.com logo in svg

Kramer RC-74DL, User Manual

Share
Download
Kramer RC-74DL User Manual Download Page 20

 

18 

RC-74DL - Technical Specifications 

 

7 

Technical Specifications 

INPUTS: 

3 RS-232, 1 RS-485, 2 GPI/O and 2 K-NET on terminal 
block connectors; Ethernet on an RJ-45 connector; 1 
infrared sensor, 1 USB for programming 

OUTPUTS: 

2 IR, 4 relays (36V AC or DC, 2A, 60VAC maximum on 
non-inductive load) and 2 GPI/O on terminal block 
connectors 

DEFAULT IP SETTINGS: 

IP number 

 192.168.1.39; Mask 

– 255.255.0.0; Gateway 

– 0.0.0.0 

POWER CONSUMPTION: 

12V DC, 570mA 

OPERATING TEMPERATURE: 

0° to +40°C (32° to 104°F) 

STORAGE TEMPERATURE: 

-40° to +70°C (-40° to 158°F) 

HUMIDITY: 

10% to 90%, RHL non-condensing 

DIMENSIONS: 

16.2cm x 2.6cm x 11.4 (6.4" x 1.0” x 4.5") W, D, H 

WEIGHT: 

0.6kg (1.4lbs) approx. 

INCLUDED ACCESSORIES: 

Power supply, Kramer K-Config Windows®-based 
configuration software 

OPTIONAL ACCESSORIES: 

IR emitter cables, KPOD-301, OWB-3G 

Specifications are subject to change without notice  at 

http://www.kramerelectronics.com

 

 

Summary of Contents for RC-74DL























Reviews:

No comments

Brands by name

Popular brands

Load more brands