background image

Technical Specifications 

 

9

5.2.2 

Locking the Front Panel 

To prevent changing the settings accidentally or tampering with the front 
panel, lock your FC-7402. Unlocking releases the protection mechanism. 

To lock the FC-7402

• 

Press the PANEL LOCK button (for about 2 seconds) until the PANEL 

LOCK LED illuminates freezing the front panel controls. Pressing a button 
will have no effect

1

, except to cause the PANEL LOCK LED to blink

2

 and 

show the value of a ProcAmp setting if its button is pressed

3

 

To unlock the FC-7402

• 

Press the PANEL LOCK button (for about 2 seconds) until the front 

panel controls unlock and the PANEL LOCK LED no longer illuminates 

6 Technical 

Specifications 

Table 5 includes the technical specifications: 

Table 5: Technical Specifications

4

 of the FC-7402 SDI to Analog Converter 

INPUT: 

1 SDI: 

SMPTE - 259M, ITU-R BT.601 (CCIR-601) 75

 on a BNC connector

 

OUTPUTS: 

1 composite video - 1Vpp/75

 on a BNC connector 

1 YC - 1Vpp/75

 (Luma), 0.3Vpp/75

 (Chroma) on a 4p connector 

1 component - RGB / Y, R-Y, B-Y (1V, 0.7V, 0.7V/75

) on BNC connectors

 

1 SDI (reclocked): 

SMPTE - 259M, ITU-R BT.601 (CCIR-601) 75

 on a BNC 

connector

 

RESOLUTION: 

10-bit 

BANDWIDTH: 

<0.5dB up to 5MHz, Fully Loaded 

NON-LINEARITY: <+/-1.0% 

DIFF. GAIN: 

0.11% (NTSC) 

DIFF. PHASE: 

0.33 deg (NTSC) 

K-FACTOR: 0.3% 

S/N RATIO: 

67dB unweighted 

YC DELAY: 

<20ns 

EQUALIZATION: 

>125m for Belden 8281 cable

 

CONTROLS: 

RS-232 and front panel: brightness, contrast, color (saturation and separate U, V), 

hue, and sharpness. Front panel lock 

POWER SOURCE: 

230 VAC, 50/60 Hz, (115 VAC, USA) 13.8 VA

 

DIMENSIONS: 

19 inch (W), 7 inch (D), 1U (H) rack mountable 

WEIGHT: 

2.6 kg. (5.7 lbs.) approx.

 

ACCESSORIES: Power 

cord 

                                                        

1 Nevertheless, even though the front panel is locked you can still operate your PC control software 

2 Warning that you need to unlock to regain control via the front panel 

3 For example, if the HUE button is pressed when the panel is locked, then the 7-segment display will illuminate the current 

value of the HUE setting 

4 Specifications are subject to change without notice 

Summary of Contents for FC-7402

















Reviews: