GB
- 22 -
ger.
4. In the section entitled „Charger indicator“ you
will
fi
nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and
fi
res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.7 Saw chain lubrication
Warning!
Always remove the battery from the
device before inspection and adjustment. Always
wear protective gloves when working on the
chainsaw to protect yourself against injury.
Important!
(Fig. 14) Never operate the chain if
it is not lubricated with saw chain oil. Use of the
chainsaw without saw chain oil or if the oil level is
below the viewing window will result in damage to
the chainsaw!
Important!
Be aware of the temperature condi-
tions: di
ff
erent lubricants with completely di
ff
erent
viscosities are required at di
ff
erent ambient tem-
peratures. At lower temperatures you will need
low viscosity oils in order to achieve a su
ffi
cient
lubricating
fi
lm. However, if the same low viscosity
oil is used during the summer it will become even
thinner due to the ambient temperatures alone,
and as a result the lubricating
fi
lm could break
down, causing the chain to overheat and become
damaged. In addition, the chain oil would burn
and produce unnecessary pollutants.
Filling the oil tank (Fig. 14)
1. Place the chainsaw on a flat surface.
2. Clean the area around the oil tank cover (Item
10) and then clean the oil tank cover.
3. Fill the tank with saw chain oil. In the process,
make sure that no dirt enters the tank, as this
could cause the oil nozzle to become blo-
cked.
4. Close the oil tank cover (Item 10).
5.8 Battery capacity indicator (Fig. 1)
Press the button for the battery capacity indica-
tor (F). The battery capacity indicator shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED
fl
ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may di
ff
er from one loca-
tion to another.
Caution!
Always use the shoulder strap when
working with the equipment. Always switch o
ff
the
equipment before you take o
ff
the shoulder strap.
Otherwise there is a risk of injury.
Anl_KX_AHE_1820_Li_SPK13.indb 22
Anl_KX_AHE_1820_Li_SPK13.indb 22
27.05.2021 11:21:00
27.05.2021 11:21:00
