1 0
ACCESSORY PF06-YJLF-F
Tools required: Phillips screwdriver
1.
From back of heater remove the
Knock-out center panel with two
brackets at the four sides with a
phillips head screwdriver (see
Figure12).
2.
Disconnect power cord wires
from blower motor (if connected)
(see Figure 13).
3.
Disconnect green ground wire
from blower housing (if connected)
by removing screw holding wire
terminal (see Figure 13).
4.
Install one rubber bushing
provided in blower kit into the
1.5
"
hole in the left rear of firebox
floor. Access hole through the
rectangular opening in the rear
panel (see Figure 14).
5.
Attach the two brackets to
blower housing using four white
screws provided in blower kit ( 2
for each bracket) (see Figure 15).
Tighten screws securely. Place
blower assembly temporarily on
top panel.
6.
Working from the rear of the
stove place entire power cord,
including operation control
h o u s i n g , i n l o w e r c o n t r o l
compartment.
Figure 12 -Removing
Stove Knock-out Panel
7.
Route ends of 4-wire power cord
and thermostat switch up from
the lower control compartment
through the rubber bushing, then
up to the upper cavity of stove
(see Figure 16).
8. Using one big black screw
provided in blower kit, mount
bracket with thermostat switch to
the left of firebox on back of
heater (see figure 16).
9.
Attach the terminal ends of the
white and black power cord wires
to the terminals on the blower
motor (see Figure 13). Push firmly.
10. Attach the terminal end of the
green power cord wire to the
front tab of the blower housing
using black screw provided (see
Figure 13).
11. P l a c e b l o w e r a s s e m b l y
temporarily on top panel.
12. Install control knob onto output
shaft of operation control housing
(see figure 16). Place operation
control housing just inside
control compartment door in front
of stove (see Figure 17).
13. Using two black screws provided
in blower kit, mount blower
operation control housing to
mounting tab in left side of lower
control compartment (see Figure
17).
14. Check to make sure that the
power cord is completely clear
of blower wheel and there are
no foreign objects in blower
wheel.
15. Using the screws removed
previously, mount blower assem-
bly to stove by reattaching the
Knock-out center panel to rear
panel (see Figure 15). Tighten
screws securely.
16. Peel off the backing paper and
stick the supplied wiring diagram
decal on the stove floor as shown
in Figure 16.
17. P l u g p o w e r c o r d i n t o a
convenient 3-prong grounded wall
receptacle near the stove.
18. Using Auto/O/Man switch, turn
blower on and check for
operation. Turn on Auto/O/Man
switch to the desired position.
On position will remain con-
stantly on. Auto position will be
controlled by the thermostat on
fan blower unit. To stop the
operation turn unit switch to the
O position.
19. All remaining parts from blower
kit may be discarded.
W A R N I N G : E L E C T R I C A L
G R O U N D I N G I N S T R U C T I O N S
This appliance is equipped with a
three-prong (grounding) plug for your
protection against shock hazard and
should be plugged directly into a
properly grounded three-prong
receptacle.
NOTICE: Shut off gas heater during
the following blower installation.
Figure 13 -Removing Wires From
Blower
Figure 15 -Attaching brackets to
blower and mounting blower
Figure 14 -Installing Bushing
Figure 17-Installing Blower Control
Housing
Figure 16 -Routing Power Cord