Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Utility Model: M 339841
Utility Model: M 339840
Tel:+886-2-89111000
Fax:+886-2-29123328
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000N7850000
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
Power the unit and connect to network Cable
1. Wiring Power Inputs
JetNet 7850G-2XG and JetNet 6852G AC Power Input
Connect the attached power cord to the AC power input connector, the available AC power
input is range from 100 ~ 240 VAC at 50 ~ 60 Hz.
JetNet 7850G-2XG-DC48 and JetNet 6852G-DC48 DC Power Input
The suggested power input is -48VDC, the available range is from -36 ~ -72VDC.
Follow below steps to wire JetNet 7850G-2XG-DC48 and JetNet 6852G-DC48 DC power
inputs.
2. Wiring Earth Ground
To ensure the system will not be damaged by noise or any electrical shock, we suggest you to
make exact connection with JetNet 7850G-2XG-DC48 and JetNet 6852G-DC48 with Earth
Ground.
LED
LED
LED
1. Insert positive and negative wires into + and - contacts respectively of the connector.
2. Tighten the wire-clamp screws to prevent DC wires from being loosened.
On the back panel of JetNet 7850G-2XG-DC48 and JetNet 6852G-DC48, there is one earth
ground screw. Loosen the earth ground screw by screw drive; then tighten the screw after earth
ground wire is connected.
Device Management
The system may be managed out-of-band through the console port on the rear panel or
in-band using Telnet, a Web Browser, or SNMP.
1. Web-based Management Interface
After you have successfully installed the Switch, you can configure the Switch, monitor the
LED panel, and display statistics graphically using a Web browser, such as Netscape Navigator
(version 6.2 and higher) or Microsoft® Internet Explorer (version 5.0).
The default IP address before configuring is 192.168.10.1. User Name is admin, default
password is admin.
After configured the layer 3 virtual interfaces, you can assign primary IP and second IP
addresses to the interface, this is known as default gateway of the lower hosts. The lower hosts
in each subnet can access the interface by the default gateway IP address.
The default IP address is only available in layer 2 mode, the layer 2 mode means there is no
any configured layer 3 virtual interface. After configured the layer 3 virtual interface, the
default IP address is changed to the assigned primary/second IP address of the interface.
Note:
To access the Switch through a Web browser, the computer running the Web browser
must have IP-based network access to the Switch. It is not suggested multiple user’s access to
the web browser. The performance of web display would be affected.
Warning: Since the lower hosts under the layer 3 interface can access the switch by default
gateway IP address. Please remember to change the user name and password in your first
login. Otherwise, the users can easily access the management interface and change the
settings. It obeys the common security concern
2. Command Line Console Interface Through the Serial Port or Telnet
You can also connect a computer or terminal to the serial console port or use Telnet to access
the Switch. The command-line-driven interface provides complete access to all switch
management features. The RS-232 DCE console port is for setting up and managing the
Switch via a connection to a console terminal or PC using a terminal emulation program. The
default baud rate is 115,200, N, 8, 1.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0).
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional staffs are
ready to solve your problems at any time Korenix global service center's e-mail is
[email protected].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
3 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
workmanship for a period of three (3) years from the date of delivery provided that the
Product was properly installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as floods, fire, etc.), other external forces
such as power disturbances, over spec power input, or incorrect cabling; or the warranted
Product is misused, abused, or operated, altered and repaired in an unauthorized or improper
way.
Support
