manualshive.com logo in svg

Korenix JetI/O 6510, User Manual, Page: 5 / 95

Share
Download
Korenix JetI/O 6510 User Manual Download Page 5

 

2 

 

1.2  Package Checklist 

Korenix JetI/O 6500 Series products are shipped with following items: 

 

One Ethernet I/O Server 

 

One attached DIN-Rail clip 

 

Terminal Blocks for I/O and Power Input 

 

Documentation and Software CD 

 

Quick Installation Guide 

If any of the above items are missing or damaged, please contact your local sales 
representative. 

 

1.3  JetI/O 6510 Introduction 

JetI/O 6510 is an intelligent I/O Server equipped with one Ethernet port and 8 

channels Analog Input connectors. JetI/O 6510 provides 16 bits resolution and high 

accuracy for I/O data collecting. The analog input range can support from 150mV 

to 10V and 20mA. The values are most adopted in the industrial environemnt. 

JetI/O 6510 provides Windows Utilities, SNMP for configuration. Industrial Modbus/ 

TCP protocol and OPC Server driver for integrating JetI/O with existed HMI/SCADA. 

Robust aluminum case with good heat dispersing and IP31 protection. With JetI/O 

users can easily perform status monitoring and control the remote I/O devices. 

 

 

Summary of Contents for JetI/O 6510
































































































Reviews:

No comments