background image

7

VII. Specific Model Data 

    Mounting 

 

 

 

 

 

 

 

 

 

 

 

 
 

Kooltronic Air Conditioners have been engineered to be installed easily. To avoid damaging your Air 
Conditioner, please read the following information before installation: 
 
1.  See Figure 1 for proper Mounting Template and Assembly Bracket (M/TAB) orientation. Place 

M/TAB against the outside of the cabinet to locate cutouts and mounting holes.

 Make sure the 

cutouts don't interfere with components inside your cabinet. 

2.  Make the necessary cutouts and mounting holes in the cabinet. NOTE: Cutouts must not be 

less than M/TAB openings. 

3.  Mount M/TAB to the outside of the cabinet using 6 sets of the mounting hardware supplied by 

Kooltronic (1/4-20 press studs, nuts and washers). NOTE: Make sure the press studs are 
inserted with heads toward you. Tighten nuts securely. 

4.  To facilitate easy mounting, the three screws located on each side of the unit should be backed 

out enough to allow the M/TAB slot to fit. 

5.  Route the power cord through the top cutout in your cabinet. Line up the three screws on each 

side of the unit with the slots on the M/TAB. Slide the unit inside the M/TAB. 

6.  Make sure there is a tight fit between the unit and M/TAB, before tightening the 10-32 self-

tapping screws. NOTE: Do not overtighten these screws. 

7.  Attach overflow drain hose supplied to the drain exit in the side of the unit. This hose must not 

be elevated above the exit port. Improper mounting will impede the flow of condensate and 
may cause internal malfunctions.

 

CAUTION 

 
 

 

If the Air Conditioner is mounted to the cabinet door you must be sure 

that the door hinges will support the additional weight of the Air 

Conditioner. Also be certain that when the door is opened fully, the 

cabinet does not become unbalanced. The actual weight of the unit can 

be found in the performance specifications.

Dimensions (inches) are for reference only and are subject to change.

MOUNTING PLAN

(6) 

1/

4

-20 WELD NUTS

WELD NUTS SUPPLIED FOR

ALTERNATE MOUNTING

METHOD TO MAINTAIN

NEMA 12.  MOUNTING PLANS

FURNISHED ON REQUEST.

M/TAB

POWER

CORD

THERMOSTAT

ADJUSTMENT

ACCESS

FILTER

(8).312 
[7.9] DIA. 
HOLES

DRAIN

FILTERED
CONDENSER AIR INLET
(Ambient Air In)

CONDENSER OUTLET
(Warm Ambient Air Out)

WARM AIR RETURN
FROM ENCLOSURE

COOL AIR OUTLET
TO ENCLOSURE

 

1

2

3

4

3

4

2

3

4

1

 12.13

 [308.1]

 17.50

 [444.5]

 9.00

 [228.6]

 12.25

 [311.2]

 .38

 [9.7]

 8.13

 [206.5]

 TYP.

 5.75

 [146.1]

 .38

  [9.7]

 .88

  [22.3]

 6.38

 [162.1]

 4.13

 [105.0]

 17.50

 [444.5]

 5.00

 [127.0]

 .50

 [12.7]

  TYP.

 .50

 [12.7]

 .38

 [9.7]

 12.25

 [311.2]

 11.25

 [285.8]

 6.13

 [155.7]

 11.25

 [285.8]

 3.13

 [79.6]

FIGURE 1

Summary of Contents for TRIMLINE K2A4C1.0NP17L














Reviews: