background image

 

 

WAKL5N0802A 

Edition: 07.02.2022 

Page: 18/18

 

 

 

 

5.4.  Mounting and demounting of the condenser fans 

 

Condenser fans are of UL series, installed in the square form. 
This allows the individual components to be connected by 
plug-in system, ensuring the structural stability.  
Disassembly of the individual segments is performed in the 
direction indicated by the arrow. In order to repair the conden-
ser fans, remove the central front cover. 

 

 
After removing the central front cover, remove 
the condenser cover. Pull the condenser fans 
out of the guiding rails in direction of arrow. 
 
 
 
Then, you can disconnect the plug connection 
and replace the condenser fan. Perform the 
assembly in reverse order. 

6.  Warranty Conditions 

The current „General Warranty Conditions KONVEKTA AG“ will apply. A copy will be furnished by 
the warranty department. Please contact: 

[email protected]

7.  Waste disposal in accordance with legal provisions 

After the phase of use the last proprietor is responsible for the adequate waste manage-
ment. The environmental regulations in the exporting country must be observed. 

The follow-

ing list contains the most important regulating literature, valid for the 

Federal Rep. of Germany

 

Resolution for dangerous substances 

 

Resolution for used oil 

 

Law for waste circulation (KRW/AfgG)) 

 

Law of water balance 

 

Resolution for the proofs of utilization and 
removal 

 

Resolution for the waste management of old cars and 
the adaptation of road prescriptions 

 

Criminal Code (StGB) 28th section „criminal 
acts against the environment” §326 - Envi-
ronment jeopardizing waste management 

 

Resolution (EC) No. 2037/2000 of the European Par-
liament and of the Council for materials that affect the 
ozone layer 

 

Law of chemicals § 27 - penal prescriptions 

 

Resolution to prohibit certain ozone destroying halo-
gen hydrocarbons. 

The used refrigerant endangers the environment. When dealing with refrigerants the existing pre-
scriptions and regulations are to be followed. 

Only qualified staff is allowed to carry out these 

works! 

Water endangering substances - acc. to §§19g-19l - are solid, liquid, and gaseous sub-

stances. e.g.: mineral and tar oils (cooling oils), halogen containing organic combinations (refriger-
ants). 



 

  

Source of supply: Bundesanzeiger, Beuth Verlag, dtv (Deutscher Taschenbuch Verlag

 

8.  History of modification 

Version  Date 

Name 

Remark 

File 

A00 

23.04.2020  B. Keßler  Source file 

WAKL5N0802A 

A01 

20.05.2020  B. Keßler  Technical data and maintenance schedule updated 

WAKL5N0802A 

A02 

07.02.2022  B. Keßler  Added 3

rd

. generation, file cpl. revised 

WAKL5N0802A 

 

Condenser cover 

Central front cover 

Summary of Contents for UL500EM



















Reviews: