background image

 

 

WAKL5N0802A 

Edition: 07.02.2022 

Page: 3/18

 

 

Introduction 

 

You will certainly understand that we will not recognize any warranty claims due to improper han-
dling, inadequate maintenance, applications that do not correspond with the determined use, utili-
zation of unadmitted fuels or the non-observance of safety provisions. 
KONVEKTA will annul without prior notice all obligations concerning guarantee, service contracts 
etc. regardless if granted by KONVEKTA or its distributors in case other than original KONVEKTA 
spare parts or parts bought from KONVEKTA AG have been used for maintenance and repair. 
These operating instructions contain all necessary information to operate your air conditioning

 

unit. 

In case you need more explanations please contact the next KONVEKTA service station. 

The machine is in accordance with the EC machinery directive 2006/42/EC. 

The unit contains or needs fluorinated greenhouse gas for operation and is subject to iden-
tification requirements in accordance with F-Gas Regulation 517/2014. 

In the course of further developments, we reserve the right to technical modifications without prior 
notice. Guarantee and liability conditions of 

KONVEKTA AG

’s general business conditions are not 

enlarged

 

by the above notes. 

Indications and photos should neither be copied and circulated nor used for competitor’s purposes. 
All rights according to the copyright remain expressly reserved. 

Manufacturer KONVEKTA AG, P.O. Box 2280, D-34607 Schwalmstadt 

Information on the operating instructions 

This maintenance instruction is valid for the a/c unit types

 

UL500EM 

 

UL700EM 

 / 2nd and 3rd Generation 

and was exclusively written for maintenance personnel. 
It contains:  

 

Maintenance Plan 

 

Maintenance Instructions 

 

Operating Instructions 

 

Repair Instructions 

Maintenance and service works have to be carried out regularly, as described in the maintenance 
schedule Bus No.: 

WP07050618

, by a 

KONVEKTA

 service station according to our maintenance 

plans. On our homepage www.konvekta.com you can find under the heading >

Service

< contact 

data of service stations nearby. 

- Only qualified staff is allowed to carry out these works! - 

For general instructions on repair 

– and maintenance works please contact via email:  

[email protected]

 

 

Danger of accidents! 

Qualified  staff in charge  of  installation and maintenance have  to  be  trained in accordance 
with EN 378-Part 4 and (EC) No.307/2008 and must strictly follow the legal provisions.

 

Any works or modifications at the air conditioner which are carried out improperly can lead 
to malfunction and so endanger operational reliability. We recommend having all works and 
modifications carried out at an authorized KONVEKTA Service Station

. Before carrying out 

any maintenance works at your air conditioning unit, carefully read the  
KONVKETA safety provisions (TD00052A)

 

in order to avoid any dangers and accidents! 

Before carrying out any maintenance works read carefully the operation instructions:   

  Operation, including troubleshooting and disposal of operating materials.  

  Maintenance

 

The maintenance instruction has to be amended by instructions based on national rules for 
accident prevention and environmental protection. 

Summary of Contents for UL500EM



















Reviews: