26776 Tiltable desktop
monitor stand
INTENDED USE
- Desktop stand individually adjustable in height and inclination
-
for monitors and many other devices of this size
FEATURES & CAPABILITIES
- Load-bearing capacity up to 25 kg centered load
- Solid, flat stand with 4-point felt support and space for cables
- Functional monitor tray (W x D 230 x 250 mm):
-
- Variable angle adjustment up to 12.5° with safety ledge
-
- Movable to ensure that the load is centered
- Variable height adjustment, double reinforced tube combination
- Data: Height 350 - 450 mm, base 250 x 210 mm, Weight: 4.15 kg
SAFETY NOTES
Thank you for choosing this product. Please read and follow carefully the instructions. They
inform you about all important steps, that are required for a safe assembly and operation. Please
keep the instructions for future reference.
A. GENERAL
A.
- Load-bearing capacity max. 25 kg centered load
A.
- Careful handling required - during all phases of use (
A - F
)
A.
- ACTIVITIES AT THE STAND (change location, extend/retract tube, adjust tray) MUST
A.
-
ALWAYS BE DONE IN UNLOADED CONDITION (e.g. danger of tipping over)
A.
- Keep unauthorized personnel away from the stand
A.
- Only to be used indoors
B. INSTALLATION NOTES
B.
- The surface (desktop) must be suitable, i.e. level and load-bearing
B.
- Wear protective gloves during assembly, if needed
B.
- In particular, during assembly do not drop - or crush limbs
B.
- Securely screw components (base, tube combination, joint, tray) together
C. STAND SETUP
C.
- Please consider the information provided in the SETUP INSTRUCTIONS
C.
- The screw connection between the stand tube and base plate
C.
-
must be screwed in as far as it will go
2.1
C.
- The weight bearing load is not to be placed on the tray until the extension tube
C.
-
height has been adjusted, i.e. when: - the catch
4.4
is always clicked into place;
C.
-
height has been adjusted, i.e. when:
- the clamping screw
4.5
has been tightened;
C.
-
height has been adjusted, i.e. when:
- the angle of the tray
c
has been adjusted and
C.
-
height has been adjusted, i.e. when:
-
the safety nut has been re-tightened
3
and
8
C.
- Note: initially the load is carefully placed on the tray and held securely.
C.
-
If the tray tilts, the nuts
8.4
have to be tightened.
C.
- The load is to be centered on the tube combination
12
, anything that is not centered
C.
-
can have a negative effect on stand stability
D. PRIOR TO USE
D.
- Prior and after use the stand should undergo visual inspection, to ensure that all
D.
-
components are there and in working order.
D.
- Damaged stands may not be used i.e. the stand must be repaired by a qualified
D.
-
technician.
E. DURING OPERATION
E.
Safety during operation is based on:
E.
1. ...FOLLOWING the points listed here under
A - F
.
E.
2. ...MASTERING the LATERAL FORCES (TIPPING DANGER).
E.
2.
Lateral forces should be avoided at all costs. It occurs in the following cases:
E.
2.
a.
the stand is tilted (uneven surface)
E.
2.
b.
the load bearing weight is not centered
E.
2.
c.
external shocks such as bumping into the stand, brushing into the stand, wind etc.
E.
2.
Lateral forces must be prevented by suitable measures. In the case of items
a.
E.
2.
and
b.
, this is done by correct assembly and placement, and in the case of item
E.
2.
c.
, possibly by safety measures or by maintaining safety distances for unauthorized
E.
2.
persons.
E. DISASSEMBLY
E.
- First remove the load from the tray - then retract or dismantle the stand
SETUP INSTRUCTIONS
1. COMPONENTS (a-m)
Please carry out a visual inspection to ensure that all parts are included and, as far as can
be seen, are OK:
a
Base plate with the four feet
b
Tube combination cpl.:
b.1
base tube,
b.2
clamp,
b.3
extension tube,
b.4
joint
c
Tray with
c.1
ledge
Accessories bag:
d
countersunk screw M8 x 20 mm -
e
caps SW10 -
f
washers ø 6.4 mm
Accessories bag:
g
lock nuts M6 -
h
caps SW13 -
i
wrench SW10/13 -
k
Allen key SW5
Accessories bag:
m
rubber pads (4x)
SETUP
2. STAND
2.1
Insert the two pins of the base tube
b.1
into the slots of the base plate and connect
2.1
both parts using the countersunk screw M8 x 20 mm
d
. Use the SW5 Allen key
k
for
2.1
this purpose.
2.2
Now set up the stand and carefully place it on the surface. To protect it, the base plate
2.2
has 4 feet with a felt pad. Tighten the loosened stand legs again with a socket wrench
2.2
(SW8 = M5).
3. MONITOR TRAY
3.1
The tray
c
is placed on the joint using the threaded bolt
b.4
and screwed together...
3.2
...with the safety nuts
g
and the washers ø 6.4 mm
f
.
3.2
To accomplish this, use the SW10
i
Allen wrench. In the final step place the caps
e
.
1. COMPONENTS
2. STAND
3. MONITOR TRAY
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
26776-000-55 Rev.03 03-79-934-00 10/21
M5 / SW8
