background image

E-14

(4) Display the Service Mode screen. 

(For details of how to display the Service Mode 
screen, see the Service Manual.)

(5) Touch “Finisher.”
(6) Touch “FS-FN adjustment.”
(7) Touch “Half-Fold Position.”
(8) Touch “ALL.”

[If the crease deviates as shown below]
Using the 

 key, set the numeric value.

[If the crease deviates as shown below]
Using the 

 key, set the numeric value.

(9) Touch “Test Copy.”
(10) Select the tray loading paper for the test copy.
(11) Touch “3.”
(12) Touch “Half-Fold”, and press the start key.
(13) Check the crease positions deviate.
(14) Touch “END” to return to the adjustment 

screen.

(15) Touch “OK” twice.
(16) Touch “Exit” on the Service Mode screen.

<Center staple position adjustment>

(1) Unfold the paper that exits the machine and lay 

the paper with the ridge facing up.

(2) Check the staple position for deviation from the 

crease (Measure width A). 
Reference: 0 ± 1.0 mm

(3) Display the Service Mode screen. 

(For details of how to display the Service Mode 
screen, see the Service Manual.)

(4) Touch “Finisher.”
(5) Touch “FS-FN adjustment.”
(6) Touch “Center Staple Position.”
(7) Check that “ALL” is displayed in reversed.

A

A

Exit direction

A

Staple position

Summary of Contents for FS-536

















Reviews: