background image

E-12

3. Adjustment procedures

Note:

Perform this adjustment only when the Finisher 
FS-536SD is installed.

(1) Plug the power cord into the power outlet and 

turn ON the power switch.

(2) Select Finishing 

 Fold/Bind.

(3) Make copies in finisher mode and check the sta-

tus of the Half-Fold, Center Staple & Fold and 
Tri-fold.

Note:

When copying in the Center Staple & Fold mode, 5 
originals need to be set on the document feeding 
tray.

<Half-fold skew adjustment>

(1) Unfold the paper that exits the machine and lay 

the paper with the ridge facing up.

(2) Check the crease for deviation

(Measure width A1 and A2).
Reference: A1 - A2 = 0 ± 1.0 mm

(3) Insert a screwdriver into the holes on the right 

side of the saddle unit shown below to loosen the 
two screws.

Note:

The screws do not line up exactly with the holes. 
Instead, they are located slightly higher than the 
holes, so access the screws by pointing the screw-
driver slightly upward when inserting it.

(4) Push up the lever unit on the left side of the sad-

dle unit, and loosen the two screws shown in the 
illustration.

If each mode are out of specifications, 
make the following adjustments.

Exit direction

<Half-Fold/
Center Staple & Fold>

<Tri-fold>

Exit direction

A1

A2

Crease

Screw

Lever unit

Summary of Contents for FS-536

















Reviews: