background image

   

 

  

 

Maintenance manual  

 

KONGSBERG PROPRIETARY. 

This document and its accompanying elements contain KONGSBERG 

information which is proprietary and confidential. Any disclosure, copying, distribution or use is prohibited if not 
otherwise explicitly agreed with KONGSBERG in writing. Any authorized reproduction, in whole or in part, must 
include this legend. ©2020 KONGSBERG - All rights reserved. 

 

P a g e  

38 | 

 

Accessing log files: 

SD card can be removed during operation without affecting functionality of the steering gear unit. 
For each steering gear 

 

Press the Remove SD card button, as shown on User interface label in CS cabinet, and Figure 3 
of this document. 

 

The SGPMS online LED (LED 7), which blinks every second, will blink twice per second as the 
system closes the file on the memory card. 

 

Once the file is closed, the SD card removal OK LED (LED 8) will turn off. 

 

Remove the SD card from the holder on amplifier card by first pushing it inwards 

 

Using the USB reader that you have received in the upgrade kit, access files stored on the SD 
card. Attach the log file with most recent date to an email and send it to: 

[email protected]

 

 

Insert the SD card into the SGPMS. 

 

Press the Reset button to activate logging functionality. You will notice all LED's illuminate for 
2-3 seconds, followed by LED 8 being lit (logging activated) and the SGPMS online LED (LED 7) 
flashing. 

 
This concludes the log file transfer procedure. 
 
 

 

Summary of Contents for SR 562










































Reviews: