Kongsberg cNODE Micro Instruction Manual Download Page 28 | Manualshive

Page: 28 / 56

background image

26

426351/A

3

Dry off the Transponder and make sure that there is no water around the On/off
plug or the external connector.

4

Turn the unit OFF by removing the On/off plug or disconnecting the external cable.

5

Recharge the unit if it is deployed again and not stored.

Result

The Transponder is ready for operation or for storage.

cNODE Micro Instruction Manual

«
...
26
27
28
29
30
...
»

Summary of Contents for cNODE Micro

























































Reviews:

No comments

Related manuals for cNODE Micro

SoundWorks Radio 820HD

Brand: Cambridge SoundWorks Pages: 12

Brand: Water Witch Pages: 2

airFiber AF-5XHD

Brand: Ubiquiti Pages: 32

A1101R09 Series

Brand: Anaren Pages: 26

Brand: Sirius Satellite Radio Pages: 68

AVENTO Sports Line Suspension Kit

Brand: Grammer Pages: 4

Brand: Kambrook Pages: 6

Brand: Laser Pages: 15

Brand: Polk Mono Pages: 24

Brand: Garmin Pages: 10

$Si-tex SAS-300 Operation Manual preview$

Brand: Si-tex Pages: 104

Brand: Sytech Pages: 7

Brand: Binatone Pages: 11

Brand: Binatone Pages: 13

Brand: AUTOHELM Pages: 10

Brand: Hyundai Pages: 11

Brand: Hyundai Pages: 11

Freefall VFF 600

Brand: Muir Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands