Kongsberg cNODE Micro Instruction Manual Download Page 19 | Manualshive

Page: 19 / 56

background image

426351/A

17

.It normally takes about 30 seconds before the charging starts and the LED indicator
starts flashing green after connecting the cNODE battery charger to the cNODE
Micro.

The LED indicator will stay green when fully charged.

The battery will be charged within 1 hour.

Result

The transponder is now ready for use.

Disconnecting the cNODE battery charger

It is very important to read the procedures before disconnecting the cNODE battery
charger from the cNODE Micro.

Prerequisites

Note

Always disconnect the cNODE battery charger from the mains (110 or 220 VAC) before
disconnecting the cNODE battery charger from the cNODE Micro.

Procedure

1

Disconnect the cNODE battery charger from mains (110 or 220 VAC).

2

Disconnect the cNODE Micro from the cNODE
battery charger.

Getting started

«
...
17
18
19
20
21
...
»

Summary of Contents for cNODE Micro

























































Reviews:

No comments

Related manuals for cNODE Micro

Brand: JB.lab Pages: 56

Brand: Hama Pages: 120

Brand: PHAROS MARINE Pages: 17

Brand: Sandstrom Pages: 36

Brand: Nexus Pages: 79

Brand: Teletek electronics Pages: 2

Brand: Salora Pages: 21

Brand: Sencor Pages: 14

Brand: Radio Shack Pages: 9

Brand: E2S Pages: 20

Brand: Grundig Pages: 15

Brand: Hyundai Pages: 9

cNODE Maxi 31 Ex d

Brand: Kongsberg Pages: 50

Brand: Faria Pages: 12

Brand: Bodet Pages: 8

Brand: Naxa Pages: 11

Brand: Sony Pages: 20

Brand: Sony Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands