5
Owner’s Manual
6SS12BEA2ACA0 / 6SS24BGA2ACA0
Operation
CONTROL PANEL
1. POWER BUTTON: Activates unit when POWER BUTTON is pressed. (Fan starts on low speed).
If power button is pressed during operation, unit stops.
2. BLOWER BUTTON: Changes fan speed from (Low) to (High) when pressed.
3. SPOT/COOL BUTTON: Activates compressor and begins producing cool air 2 minutes after button is pressed.
Regulates temperature based on discharge air temperature.
4. ROOM/COOL BUTTON: Activates compressor and produces cool air 2 minutes after button is pressed.
Regulates temperature based on Return/room air temperature.
5. SET TEMP BUTTONS: Change target temperature/data value by +/- 1. Change data value by +/- 10 by holding.
Press the SET TEMP BUTTONS to set temperature.
Upper button is to heighten temperature and Lower button is to lower temperture.
6. ALARM: Alarm indicator lights (blinks) and indicates abnormal system operation. If Alarm occurs, compressor
stops.System operation stops when ALARM light is activated (blinks) longer than 3 minutes.
7. CURRENT TEMP: Displays current room temperature in display in Farenheit. (In Room Cool Mode only).
SPOT/COOL Mode – Displays outlet (cool air) temperature during normal operations. ALARM codes blink
and are displayed when abnormal operation occurs.
8. TARGET TEMP displays the unit set temperature for ROOMCOOL mode only.
TIMER: Enter to Timer setting mode if you press SPOT/COOL button and ROOM/COOL button together for
3 seconds. Press UP/DOWN button to set the timer until it shows the figure you want to set. After 3
seconds, the figure will be memorized and compressor will stop after the time set.
Figure 7
5
6SS12BEA2ACA0 / 6SS24BGA2ACA0
Owner’s Manual
5
WSC-4000 / WSC-6000
Owner’s manual
Operation
CONTROL PANEL
1. POWER BUTTON: Activates unit when POWER BUTTON is pressed. (Fan starts on low speed).
If power button is pressed during operation, unit stops.
2. BLOWER BUTTON: Changes fan speed from (Low) to (High) when pressed.
3. SPOT/COOL BUTTON: Activates compressor and begins producing cool air 2 minutes after button is pressed.
Regulates temperature based on outlet cool air temperature.
4. ROOM/COOL BUTTON: Activates compressor and produces cool air 2 minutes after button is pressed.
Regulates temperature based on inlet ambient air temperature.
5. SET TEMP BUTTONS: Change target temperature/data value by +/- 1. Change data value by +/- 10 by
pressing continually.
Press the SET TEMP BUTTONS to set temperature.
Upper button is to heighten temperature and Lower button is to lower temperture.
6. ALARM: Alarm indicator lights (blinks) and indicates abnormal system operation. If Alarm occurs, compressor
stops.System operation stops when ALARM light is activated (blinks) longer than 3 minutes.
7. CURRENT TEMP: Displays current room temperature in display in Celsius. (In Room Cool Mode only).
SPOT/COOL Mode – Displays outlet (cool air) temperature during normal operations. ALARM codes blink and
are displayed when abnormal operation occurs.
8. TARGET TEMP displays the unit set temperature for ROOMCOOL mode only.
TIMER: Enter to Timer setting mode if you press SPOT/COOL button and ROOM/COOL button together for
3 seconds. Press UP/DOWN button to set the timer until it shows the figure you want to set. After 3
seconds, the figure will be memorized and compressor will stop after the time set.
Figure 7
1
2
3
4
5
6
8
7
4
WSC-4000 / WSC-6000
Owner’s manual
Unlock the casters and push the unit using the side handles to a flat, level surface and set the caster brakes to
the locked position.
Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present, wipe off with
a clean, dry cloth.
Check the power cord, plug and prongs for damage or excess play.
If any damage or excess play is found, contact a qualified repair technician or a qualified electrician to perform
replacement or repair of the power cord, plug or prongs.
NOTE
: Make sure the AC outlet is free of dirt, dust, oil, water, or any other foreign material.
Do not use the unit in explosive environments or in areas where flammable
gas leakage may occur.
If the power cord or plug is damaged, repair should only be performed by
qualified electrical personnel.
Do not connect / disconnect the power cord or attempt to operate buttons with
wet hands. This could result in electrical shock.
Do not install the unit on uneven or sloping surface. The unit may roll or topple
over even if the casters are set to the locked position.
Do not use the Indoor unit in areas where it will be exposed to rain or water.
Do not use the unit in a corrosive atmosphere.
Do not use the unit above 18°C(64.4°F) ~ 52°C(125.6°F).
Installation
WARNINGS REGARDING PROPER LOCATION FOR INSTALLATION
MOVING THE UNIT
PLUGGING IN THE UNIT
HOW TO CONNECT THE LINES BETWEEN INDOOR UNIT AND OUTDOOR UNIT
Assembly(Continued)
Connect between the same numbers.
1. Power cord : To supply power to the outdoor unit.
2. Drain hose : To drain condensate to the outside.
3. Cooling water line and coupling (Cool water)
4. Cooling water line and coupling (Hot water)
NOTE
: Cooling water lines are 5 meters or
10 meters in length. please check with
the shop you bought this unit.
1 2
3
4
Figure 5
Figure 6
IN
OUT
INDOOR UNIT
OUTDOOR UNIT
1
3
4
2
IN OUT
