Kold-Draft AKD-125 Installation And Operation Manual Download Page 18 | Manualshive

Page: 18 / 32

background image

18

ELECTRICAL INFORMATION

REMOVING FROM SERVICE

When the ICE MAKER is determined to be no longer useable please be sure that it is rendered
safe for storage or disposal. All applicable recycling measures should be exercised to avoid
injury and harm to the environment.

The manufacturer and/or seller is/are not responsible for any harm to people, animals,
property, and the environment caused by incorrect installation and/or disposal.

«
...
16
17
18
19
20
...
»

Summary of Contents for AKD-125

































Reviews:

No comments

Related manuals for AKD-125

Tough Guy 40CA23

Brand: Grainger International Pages: 9

Brand: Party Robotics Pages: 12

Brand: Hamilton Beach Pages: 14

Brand: NatureWater Pages: 27

Brand: NatureWater Pages: 27

Brand: Grindmaster Pages: 72

Brand: Hongda Holding Water Technology Pages: 4

Brand: Clean Water Systems Pages: 22

Brand: Elkay Pages: 4

Brand: Elkay Pages: 4

Brand: Elkay Pages: 5

Brand: Zerica Pages: 13

SMARTERHOME KASPTDISPBA

Brand: Kogan Pages: 20

Brand: Wagner Ewar Pages: 20

Brand: Ugolini Pages: 44

Barrilitos Beverage Tower

Brand: lancer Pages: 22

X Factor Series

Brand: Lancaster Water Treatment Pages: 16

Brand: Fast & Fluid Management Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands