background image

4

111864-2-

BA

 (-)

Kohler Co., Kohler, WI

TO INSTALL NEW TOILET

Place new toilet upside down on padding. Firmly place
gasket on toilet outlet.

NOTE:  If using gasket with integral plastic sleeve, make
sure the gasket is positioned facing away from the toilet.

Remove rag from closet flange before setting toilet.

Carefully align and lower toilet over the closet flange and
bolts.

CAUTION: Do not lift or rock toilet after placement;
a new gasket must be reapplied if you break the
watertight seal.

Apply full body weight to toilet rim to set seal.

Fig. #5

Toilet Outlet

Gasket

Assemble bolt cap bases, washers, and nuts on exposed
T-bolts. Hand-tighten nuts, then tighten additional 1/2-turn
with wrench.

CAUTION: Overtightening may cause breakage
or chipping.

If T-bolts extend more than 1/4” from top of nut, cut off ex-
cess. Wipe away any residue. Install bolt caps.

Fig. #6

Nut

Washer

Bolt Cap Base

Bolt Cap

TO INSTALL NEW TANK

Make sure the three tank bolts extend fully through the
holes in the gasket. Set the tank onto the bowl using the
bolts as a guide. Center the gasket on the inlet of the bowl.
Assemble the washers and brass hex nuts onto the bolts.

CAUTION: Overtightening may cause breakage
or chipping.

Alternately tighten the three brass hex nuts so that the top
of the tank is level with the top of the bowl and a watertight
seal is obtained.

Fig. #7

Tank Bolt

Gasket

Washer

Nut

Summary of Contents for WELLWORTH LITE K-4229









Reviews: