background image

 

 

the drain line.   

A.Hang the bowl on the bracket 

and check tail pipe alignment, 

 then remove the bowl and adjust the bracket as needed. 

Re-hang and re-check bowl  

alignment with 

 Tail pipe should align with center of drain line. 

 

B. Mark anchor holes 

then remove 

bowl without moving hanger bracket. 

 

 

 

A.Find the drain nipple depth

 on the Tube 

B.

 

Cut the tube

 at the groove using a sharp 

utility knife to ensure a square, flat cut. 

C.

 

Clean burrs 

from the cut end by using 

emery paper.

D.

 

Apply lubricant

 to the outside of the rubber bushing and  

ribbed inside area. 

E.

 

Insert the tube 

and bushing with arrow tab at the top. 

 Apply lubricant to tailpipe of housing. 

USE UTILITY KNIFE TO CUT CAULK

 then 

use a putty knife and mallet to remove the 

bowl. Remove hanger brackets, scrape off 

caulk, and clean the wall. 

.

 

DETERMINE THE DRAIN NIPPLE DEPTH

by measuring the distance between the back  

of the sanitary tee (or elbow) to the front  

edge of the nipple.

IMPORTANT: 

Use a drain machine to remove 

build-up inside pipes. Clean up to 25 feet deep 

then flush with water to remove cutting debris. 

Never install on copper DWV.

 

A. Clean face 

of existing wall flange. 

B. Install the brass flange

 with the clear inspection disc. 

C. Slowly pour water

 into the drain.

D. Use a flashlight to check the pitch/slope 

No water

 should be present in the inspection disc or nipple.  

E. Remove flange

 after inspection.

ADJUST DRAIN TO ACHIEVE PITCH 

only if

 

standing water is present (code requires ¼"drop  

per foot of drain line for proper pitch). Seal wall  

according to code.

PLACE THE SEAL INTO THE 

FLANGE

 with the ribs facing 

out. Install the flange with 

washers and hex nuts, but 

do not tighten completely.

HANG THE BOWL,

 inserting 

tailpipe into bushing, then 

install anchor screws with 

washers.

 TIGHTEN FLANGE 

BOLTS AND GEAR CLAMP.

POUR 5 

GALLONS 

OF WATER

as rapidly as 

possible into housing 

to ensure good flow and no    

leaks or standing water. 

 

INSTALL THE GEAR 

 CLAMP 

with screw 

head at bottom, but 

do not tighten.

 

 

DRILL HOLES 

with 5/16” 

masonry bit for the lower 

anchor screws and insert 

plastic anchors.

The information in this document is 

subject to change without notice.  

©2015 Falcon Waterfree Technologies, 

LLC. All rights reserved. 

FalconWaterfree.com

CAULK THE BOWL TO THE 

WALL 

if there is good flow 

and no leaks or standing

water.

CARTRIDGE

 

INSTALL 

per the cartridge instruction 

 sheet.

 

Check rough-in height to achieve 24" 

rim height (17" rim height for ADA).

 Check slope. Downhill slope, per code, 

is essential because waterfree urinals 

require gravity flow for drainage.

 Check DWV material. Suitable materials 

include cast iron, PVC, ABS, and 

galvanized steel.

• 

Never install on copper DWV due to 

copper’s susceptibility to corrosion

.

 

Shut off water supply and cap the nipple

with the ¾" chrome cap (provided).

 

Measure drain nipple depth (in inches)

   to find trim length (in inches)

 

13 

7 8

 " or more

 DO NOT CUT TUBE

 

3 ¾" or less

 DO NOT USE TUBE

BEFORE STARTING INSTALLATION

TUBE CUTTING CHART

F1000

RETRO-FIT INSTALLATION 

WATERFREE URINAL

[email protected]

CUSTOMER CARE

2" side cutter blade

Cut away wall

Lift drain line & brace 

with mending plate

Install additional

screws here

INCORRECT

Not centered

CORRECT

Centered

11

10

12

 

CARTRIDGE 

INSTRUCTIONS

CAUTION

 After removing any urinal from the 

drain line, it’s normal for certain naturally occurring 

but

 potentially hazardous sewer gases 

to escape 

through the opening until the waterless cartridge 

is installed properly into the waterless urinal. If you 

need to leave an open drain line unattended after 

removing the urinal from the wall, temporarily wedge paper towels or a 

rag into the drain hole to reduce any outflow of sewer gases, and remove 

the paper towels or rag prior to completing the urinal or cartridge 

installation. 

Never smoke, have an open flame, or place your nose or 

mouth near open drain lines or waterless urinal housings into which 

a cartridge is not yet properly installed. 

You also can wear a breathing 

mask when removing or installing any waterless urinal or cartridge to 

reduce potential exposure to any such gases.

OR LESS

TRIM

13 ¾"

¾

"

13 ½

½

13 ¼

¼

13

1

12 ¾

12 ½

12 ¼

12

2

11 ¾

11 ½

11 ¼

11

3

10 ¾

3 ¾

10 ½

3 ½

OR LESS

TRIM

10 ¼"

3 ¼

"

10

4

9 ¾

4 ¾

9 ½

4 ½

9 ¼

4 ¼

9

5

8 ¾"

5 ¾

8 ½

5 ½

8 ¼

5 ¼

8

6

7 ¾

6 ¾

7 ½

6 ½

7 ¼

6 ¼

7

7

OR LESS

TRIM   

6 ¾"

7 ¾

"

6 ½

7 ½

6 ¼

7 ¼

6

8

5 ¾

8 ¾

5 ½

8 ½

5 ¼

8 ¼

5

9

4 ¾

9 ¾

4 ½

9 ½

4 ¼

9 ¼

4

10

21½

 

Install plastic anchor 

and screw here

15

16

4

14

7

3

13

9

6

2

11

12

10

8

5

1

1

2

3

4

Arrow 
tab UP

1

2

3

4

A

C

B

D

E

B

C

D

A

B

existing bearing rods 

LEVEL THE BRACKET THEN MARK,

 drill and install 

two additional plastic anchors and screws. If pre- 

can be used, screws are 

not necessary.

MEASURE & MARK THE ROUGH-IN 

is in-wall 

 

drill hole, then install the hanger bracket with

one plastic anchor and screw. 

carrier is not used. Use a 5/16” masonry bit to

Cutting Chart (left).  

Measure and mark the 

specified trim length 

on the insert tube at 

the nearest 1/4” groove.  

310-209-7250 

Reviews: