background image

10

1486928-W2-A

European Conformity Information

Disposal and Recycling

This range of electric showers complies with the following European directives:

2014/35/EU - Low Voltage Directive (LVD),

2014/30/EU - Electromagnetic Compatibility Directive (EMC),

2011/65/EU - Restriction of Hazardous Substances Directive (RoHS)

This range of electric showers are high power appliances and are subject to 

conditional connection. If the main electrical supply fuse is rated less than 80 Amps, 

the local electricity supply company must be contacted to confirm if the electrical 

supply is adequate. 

This range of showers complies with the requirements of the UK’s water regulations.

This product has been designed 

for domestic use only

, Mira Showers guarantee 

this product against any defect in materials or workmanship for a period of 

two years

 

from the date of purchase (shower fittings for 

one year

).

For Terms and Conditions refer to the back cover of this guide.

Guarantee

End of Product Life

Electrical and electronic devices contain a range of materials that can be separated 

for recycling and used in new products. 

This product should not be disposed of with your general household 

waste. When this product has reached the end of its serviceable life, 

please remove any batteries and take it to a recognised WEEE (Waste 

Electrical and Electronic Equipment) collection facility such as your local 

civic amenity site for recycling.

Your local authority or retailer will be able to advise you of your nearest recycling 

facility.

Summary of Contents for mira GO

































Reviews: