background image

5

29

Fig. 5.2

50 Nm

D

B

D

E

A

A

C

Fig. 5.1

Fig. 5.3

INFORMATION ABOUT REPLACEMENTS

EN

5.1 Engine oil replacement

 

Important

• Place  engine  on  level  surface  to  ensure  accurate 

measurement of oil level. 

NOTE:

  Perform  this  operation  with  warm  engine,  to  get  a 

 

better fluidity of the oil and get a full discharge of oil  

 

and impurities contained in it.

1 -

  Loosen the oil filler cap 

A

 

(Fig. 5.1)

.

2 -

  Remove the oil dipstick 

B

3 -

  Remove  the  oil  drain  plug 

D

  and  the  gasket 

E

 

(the oil drain plug is on both sides of the oil sump).

4 -

  Drain oil in an appropriate container. 

 

(For 

the 

exhausted 

oil 

disposal, 

refer 

to 

Par. 5.6 DISPOSAL

 

and

 

SCRAPPING

).

5 -

  Replace gasket 

E

.

6 -

  Tighten the drain oil plug 

D

 (tightening torque at 3

5 Nm

). 

7 -

  Add  the  type  and  amount  of  oil  recommended 

(

Tab.  1.1

 

an

Tab. 1.2

)

.

8 -

  If  the  plug 

A

  is  not  accessible,  use  the  oil 

filler cap 

C

 

Important

• Do not exceed the MAX level on the dipstick. 

Danger

Disconnect the negative wire (-) from the battery to avoid accidental engine starting.

UM KDI 1903TCR_2504TCR _ cod. ED0053029490 - 

2° ed

_rev. 

01

Index

Summary of Contents for KDI-1903TCR









































Reviews: