background image

SYMPTOMS

A. Turn on pump.
B. Check for loose connections or wires

leading from backjet pulse canister to
control. Replace backjet pulse canister or
control if necessary.

C. Fill whirlpool so water level sensors are

covered.

D. Replace actuator switch.
E. Check for loose connections or wires

leading from the pump motor to the control.

F. Remove blockage.
G. Reconnect or replace switch wires that

use modular plug.

PROBABLE CAUSES

15.Backjets do not

operate.

A. Whirlpool pump is not operating.
B. Backjet butterfly valve does not open.
C. Not enough water in whirlpool.
D. Actuator switch does not work.
E. Power from pump motor to control is off.
F. Backjet pipe is blocked.
G. Switch wire from switch to control is

disconnected.

A. Check for loose connections or wires

leading from pulse canister to control.
Replace pulse canister or control if
necessary.

B. Replace switch.
C. Reconnect or replace switch wires that

use modular plug.

16.Backjets do not

pulse.

A. Pulse canister does not work.

B. Switch does not work.
C. Switch wire from switch to control is

disconnected.

Troubleshooting the Beckjet Syetem

A.
B.

C.
D.
E.
F.
G.

15.

A.
B.

C.
D.
E.
F.
G.

A.

B.
C.

16.

A.

B.
C.

18

RECOMMENDED ACTION

1141609-T01-A

Summary of Contents for K-1111-VLN-0




















Reviews: