Kohler COM7.5 Service Manual Download Page 29

Page: 29 / 64

TP-6120 5/02

Section 3 General Troubleshooting

Is the

controller
fault LED

lit?

Yes

Correct fault

and resume

troubleshooting.

Have fuel supply

installer purge

air.

Are spark plug wire

connections okay?

Reconnect and/or

tighten.

Does the battery lose

charge while the

system is running?

Check the battery charging

system.

Is air cleaner

plugged?

Possible generator set

overload. Does reducing

load solve problem?

(Open circuit breaker to

reduce load.)

Clean or replace air

cleaner elements.

Yes

Reduce the load to keep

it within the rated range.

Lacks Power or Runs Erratically

Yes

Are spark plugs okay?

See Section 2.6.2.

Regap or replace.

Yes

Go to

Is fuel

pressure

7-11 in. water?

Yes

Have fuel supply installer

correct fuel pressure

problem.

Ensure that the

main connector is
tightly connected.

Yes

Has air

been purged

from fuel

lines?

Summary of Contents for COM7.5

































































Search results

Summary of Contents for COM7.5

Reviews:

Brands by name

Popular brands

Kohler COM7.5, Service Manual

Search results

Summary of Contents for COM7.5

Reviews:

Brands by name

Popular brands