Kohler 4EFCD-Low CO Service Manual Download Page 18 | Manualshive

Page: 18 / 88

background image

TP-6391 9/08

18

Section 3 Troubleshooting

Troubleshooting Chart

Problem

Possible Cause

Corrective Action

Reference

Generator

d

Weak or dead battery

Recharge or replace battery.

Generator O/M

set does
not crank

Battery connections

Check for reversed or poor battery connections.

—

not crank

Open circuit in engine/controller
connections

Check for loose connections.
Check the wire harness continuity.

Section 7

Blown fuse F2, controller

Replace fuse; if fuse blows again, check circuit and
components.

Section 5.12
Section 7

Blown fuse F2, relay interface
b

d (RIB)

Replace fuse.

Section 5.12

,

y

board (RIB)

If fuse blows again, disconnect the board leads one at a
time to identify the cause of the blown fuse:
Lead 70A
Leads FP and FN at the rotor
Repair or replace the component causing the blown
fuse.

Section 7

If fuse continues to blow and the previous step did not
identify the cause, check the continuity of leads FP and
FN and the leads from the P14 connector. Replace any
bad leads. Use a pin pusher, part #241918 (large) or
241919 (small) to remove leads from the connector, if
necessary. If replacing the leads does not solve the
problem, replace the RIB.

Section 7
Section 4.6

Crank relay on relay interface
board (RIB)

Check connections to the RIB. Check for 12VDC to the
RIB on lead 71N.

Section 4.6
Section 7

Check for a good ground connection (lead N).

Section 7

Check crank relay K2 operation (LED3). Replace the
RIB if relay does not operate.

Section 4.6

Generator set master switch

Check connections to the master switch on the
ADC 2100.

Section 4.3
Section 5.13

Test function of switch.

Section 5.13

Poor ground (--) connection

Clean and retighten.

—

Starter

Check starter connections.

Section 7

Rebuild or replace starter.

Engine S/M

Controller

Check controller connections and operation. Check for
power to the controller. Move generator set master
switch to OFF/RESET and then to RUN.

Section 4
Section 7

Blown F3 fuse

Verify line circuit.

Section 7

Blown F6 fuse

Check voltage regulator wiring.

Section 7

Blown F7 fuse

Check wiring for open grounds or loose connections.
Also, check for pushed out pins.

Section 7

«
...
16
17
18
19
20
...
»

Summary of Contents for 4EFCD-Low CO

























































































Reviews:

No comments

Related manuals for 4EFCD-Low CO

Brand: Wacker Neuson Pages: 254

Brand: Aksa Pages: 50

Brand: DK-Technologies Pages: 90

Brand: Whistler Pages: 2

Brand: Future Illuminations Pages: 2

Brand: StarTech.com Pages: 10

Brand: Enerdrive Pages: 2

Brand: Patton electronics Pages: 7

Brand: Sencore Pages: 126

Brand: MPP Solar Pages: 4

Brand: TAMS Pages: 30

Brand: Planet Pages: 20

Frenic Mini FRN001C1E-2U

Brand: Fuji Electric Pages: 196

Brand: M-system Pages: 4

Brand: Audio Nemesis Pages: 10

Brand: Axis Pages: 40

Brand: Lika Pages: 104

Brand: OneFex Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands