Kohler 40EFOZDJ Page 9 Installation Instructions Manual Download

Page: 9 / 16

TT-1601 5/16

Corner Cover Installation

GM86016-

1. Corner cover (GM86036 qty. 4) and pan head machined

screws (M965A-06020-20 qty. 12)

Figure 16

Corner Covers

9.1 Position the corner covers (GM86036 qty. 4) as

shown in Figure 16 using 3 pan head machined

screws (M965A-06020-20) per corner cover.

10. Install the roofs.

GM86016-

1. Alternator roof (GM86102, GM86103, GM88901 or

GM88915)

2. Engine roof (GM86097 or GM88898)

Figure 17

Roofs

10.1 Position the alternator roof (GM86102, GM86103,

GM88901 or GM88915) and engine roof

(GM86097 or GM88898) onto the sound

enclosure as shown in Figure 17.

Attach the alternator roof to the mounting brackets

in the top rail and secure using four wing nuts

(X-276-9). See Figure 15 for more detail.

Attach the engine roof to the mounting brackets in

the top rail and secure using three wing nuts

(X-276-9). See Figure 15 for more detail.

Note:

Final tighten all hardware.

Summary of Contents for 40EFOZDJ

















Search results

Summary of Contents for 40EFOZDJ

Reviews:

Related manuals for 40EFOZDJ

Brands by name

Popular brands

Kohler 40EFOZDJ, Installation Instructions Manual

Search results

Summary of Contents for 40EFOZDJ

Reviews:

Related manuals for 40EFOZDJ

Brands by name

Popular brands