Kohler 1237791-2-G Installation And Care Manual Download | Manualshive

Page: 3 / 38

background image

Tools and Materials

Before You Begin

NOTICE:

Adequate floor support must be provided. Note the

model number

on the components end of

the bath, then visit the product page at www.kohler.com for additional information.

NOTICE:

Do not lift the bath by the piping or blower, or use the piping or blower for structural support

of the bath. To avoid damage to the bath, lift by the rim at the sides of the bath.

NOTICE:

Before installing a rim-mount bath faucet, refer to the specification sheet on the bath product

page at www.kohler.com.

NOTICE:

For remote blower installations, refer to the installation instructions included with the remote

blower installation kit K-1446 before proceeding.

NOTICE: For -G2M Music Models:

Refer to the installation instructions included with the amplifier for

wiring and installation details. Position the amplifier anywhere within the shroud (not recommended) or
in a remote location. If installed within the shroud, the amplifier will need to remain plugged into the
electrical outlet at all times.

NOTICE: For -G2M Music Models:

This installation requires installation of an electrical outlet within 24

″

(610 mm) of the amplifier location. Refer to the amplifier installation instructions.

Observe all local plumbing and building codes.

Unpack and inspect the bath and components for damage. Return the bath and components to the
carton until installation.

To simplify future maintenance, make sure all plumbing and control board connections around the
bath are easily accessible.

Use conduit to route electrical wires from the circuit breaker.

Carefully plan moving the bath into the installation area. This bath will not easily fit through
doorways.

Two people are needed to install this product.

Install the bath to an adequately supported, level finished floor.

This bath is designed for freestanding installation only.

If installing a rim-mount faucet, make sure there is no interference with the drain overflow before
drilling any holes. Consult local and national codes for minimum air gap requirements if installing a
spout on the rim. Refer to the faucet specification sheet.

Plus:
•

Drop Cloth

• Shims
• 2x4
• Wood Blocks
• Gloves

Construction
Adhesive

100% Silicone Sealant

Kohler Co.

3

1237791-2-G

«
1
2
3
4
5
...
»

Summary of Contents for 1237791-2-G







































Reviews:

No comments

Related manuals for 1237791-2-G

Whitehall Extremity E-15-S

Brand: Morris Pages: 24

Bath and Wall Surrounds 6103 Series

Brand: Sterling Pages: 40

Brand: Paradise Datacom Pages: 16

VIOLET CA401004

Brand: CAHABA Pages: 10

Brand: Kinedo Pages: 2

Brand: Boffi Pages: 12

Integrated Double Clawfoot

Brand: American Bath Factory Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands