background image

ORV16

ORV20

ORV25

ORV32

ORV40

ORV50

3.2 [2.4]

6.3 [4.6]

12 [8.9]

30 [22]

60 [44]

100 [74]

0.5 [0.4]

1.2 [0.9]

1.6 [1.2]

3.2 [2.4]

6.3 [4.6]

10 [7.4]

0.5 [0.4]

1.2 [0.9]

1.6 [1.2]

3.2 [2.4]

6.3 [4.6]

10 [7.4]

20 [4.5]

32 [7.2]

50 [11.2]

80 [18.0]

120 [27.0]

200 [45.0]

20 [4.5]

32 [7.2]

50 [11.2]

80 [18.0]

120 [27.0]

200 [45.0]

20 [4.5]

32 [7.2]

50 [11.2]

80 [18.0]

120 [27.0]

200 [45.0]

Mp

N

m

[ft

lbf]

Mr

N

m

[ft

lbf]

My

N

m

[ft

lbf]

W

1

N [lbf]

W

2

N [lbf]

W

3

N [lbf]

40 [9.0]

70 [15.7]

120 [27.0]

200 [45.0]

300 [67.4]

480 [107.9]

40 [9.0]

70 [15.7]

120 [27.0]

200 [45.0]

300 [67.4]

480 [107.9]

20 [4.5]

35 [7.9]

60 [13.5]

100 [22.5]

150 [33.7]

240 [54.0]

W

1

N [lbf]

W

2

N [lbf]

W

3

N [lbf]

Although the slit type rodless cylinders 

ORV

series can be used with directly applying loads, make sure

that the load and moment do not exceed the values in the table below. In addition, since load capacity
may vary depending on the speed, confirm the rubber bumper and shock absorber absorption capacity
on p.1055 before use.

Selection

Allowable load and moment

許容負荷・モーメント

Mr=Fr×r2

r2

F

r

許容負荷・モーメント

Mp=Fp×r1

Fp

r1

許容負荷・モーメント

W

1

W

2

W

3

許容負荷・モーメント

My=Fy×r3

F

y

r3

No shock absorber

With shock absorber

: Mp

Fp

×

r1(N·m)

: Mr

Fr

×

r2 (N·m)

: My

Fy

×

r3 (N·m)

: W

1

,W

2

,W

3

(N)

Pitching moment
Rolling moment
Yawing moment
Maximum load capacity

Model

Direction of

moment 

Caution:

The moment including the inertial force generated when the load is moved or stopped
must not exceed the values in the above table.
Keep the mass and speed within the range of the rubber bumper and shock absorber 
capacity graphs.

1054̲1067ORVシリーズ̲ENG  07.9.10  1:58 AM  ページ1054

Summary of Contents for ORV16
















Reviews: