background image

・Always  connect  to  an  outlet  with  grounding  electrode  in

order  to  prevent  electrostatic  charging  of  the  whole  unit
and to make use of full performance of the Ionizer.

・ When  using  an  outlet  without  grounding  electrode

unavoidably, always use F.G.  screw (M3) located beside
the  duct  to  connect  for  grounding.    Check  to  ensure  that
the lead wire for grounding is not damaged.

4-1. Precautions on Installation of the ION WIPER

・ Use  the  ION  WIPER  indoors.    For  installation  of  the  unit,  care  should  be  taken  to  the

contamination by oil or water, high temperature and high humidity.

・Especially, avoid a place subject to dew condensation.
・Install the unit on a solid and flat surface such as a working bench.  Avoid unstable places.
・Prevent the installed metal cap of the Ionizer from contacting its metal frame, etc.

4-2. Exhaust Duct

Take care with fan.

14

-

4. Installation, Wiring and Tubing

4-3. Power Supply

・Apply 100VAC (50/60Hz) for power supply of the unit.

4-4. Wiring for Grounding

φ76.3

Note:    When  used  with  defective  grounding  of  the  ION

WIPER,  static  charge  elimination  and  dust  removal
performance will degrade.

F.G.(M3)

4-5. Air Tubing

・Use urethane or nylon tube with outer diameter of φ8 for

air tubing to the ION WIPER.

・The ION WIPER is designed to remove dust accumulated

on  the  workpiece  (charged  object).    Supply  clean  air  that
passes through a dryer or filter.

Connection Port 
for Air tubing
(φ8 quick fitting)

・ Outer  diameter  of  the  exhaust  duct  is φ76.3.    Caution

should  be  exercised  for  exhaust  resistance  when
connecting  such  as  exhaust  hoses.  (Recommended
nominal diameter of the exhaust hose: φ75)

DTY-WCM-□ has  a  blower  fan  inside  the  duct.    Be
careful not to be injured by the fan or damage of the
fan.

4-6. Installation of Expanded Metal

・Install the expanded metal from the front side of the main

body as shown in the picture.  Align cutout portion of the
expanded metal (one place for A4, two places for A3) with
the top of the 

photoelectric switch.

Handle the expanded metal carefully as the cut section

is very sharp.

Expanded metal

Caution

Caution

Caution

Summary of Contents for ION WIPER DTY-WC-L















Reviews: